IEI Technology ROCKY-6614 Скачать руководство пользователя страница 194

Страница: 194 / 204

-19

CKY-6614 WSB- Card

194

IEI

Technology, Corp

E.2.3 Install

SATA

Drives

To implement the on-chip RAID function, two SATA drives must be connected to the

system. To do this use the SATA drive cables that came with your system to connect the

SATA drives.

E.2.4

Configure the SATA Controller in BIOS

To configure the RAID BIOS, follow the steps below:

Step 1:

Turn on the motherboard and enter the BIOS setup utility. Do this by clicking

ELETE

when the system boots up.

Step 2:

Select the

Advanced

settings menus.

Step 3:

Select the

IDE Configuration

sub-menu.

Step 4:

In the

IDE Configuration

sub-menu select the “

Onboard PCI S-ATA

Controller

” option (see

Section 5.3.2

BIOS IDE Configuration

on page 81).

Step 5:

Set the “

Onboard PCI S-ATA Controller

” option to the “

Raid Mode

” and hit

NTER

Step 6:

Save your changes and exit the BIOS setup utility. To do this, hit the escape key

and select the

Exit

menu from the top menu bar in the BIOS utility setup.

Step 7:

When you enter the

Exit

menu, select the “

Save Changes and Exit

” menu

option.

Step 0:

E.2.5

Configure the RAID BIOS

The next step is to configure the BIOS RAID. To do this, follow the steps below.

Step 1:

Restart your system. Wait for the POST to be complete.

Step 2:

You will be prompted to press <

TRL

and <

> to enter the BIOS RAID Setup

Utility (see

Figure E-4

Содержание ROCKY-6614













































































































































































































Результаты поиска

Содержание ROCKY-6614

Отзывы:

Похожие инструкции для ROCKY-6614

Бренды по названию

Популярные бренды

IEI Technology ROCKY-6614, Руководство пользователя

Результаты поиска

Содержание ROCKY-6614

Отзывы:

Похожие инструкции для ROCKY-6614

Бренды по названию

Популярные бренды