IEI Technology ROCKY-6614 Скачать руководство пользователя страница 24

Страница: 24 / 204

-24

CKY-6614 WSB- Card

IEI

Technology, Corp

2.5 Graphics

Support

The graphics features listed below are all integrated on the SiS661CX northbridge chipset.

AGP 3.5 and AGP 2.0 Compliant

AGP 8X/4X mode support

Fast Write support

1.5V interface support only

DX9 S/W Compliant

High performance 256Bit 3D/128Bit 2D Graphic Engine

2 pixel rendering pipelines and 4 texture units per cycle (2P4T)

Up to 200 MHz ECLK

SiS Ultra-AGPII™ Technology w/ up to 3.2GB/s Data Transfer Rate

Successor of Ultra-AGPII™ Technology and doubles the bandwidth

up to 3.2GB/s with DDR400

AGP 8X equivalent bandwidth for 3D/2D/Video

Advanced Hardware Acceleration for DVD playback

Dual 12-bit DDR Digital Interface for Digital LCD/TV-OUT support

NTSC/PAL TV-OUT

LCD Monitor

Dual view function support for LCD-TV,LCD-CRT or CRT-TV

Built-in high performance 333MHz RAMDAC

Graphics support mode

CRT highest resolution mode: 2048x1536x32@75NI

LCD highest resolution mode: 1600x1200x32@ 60NI

TV highest resolution mode: 1024x768x32@60NI

2.6 Memory

Support

The ROCKY-6614 CPU has two 240-pin dual inline memory module (DIMM) sockets and

supports up to two un-buffered DDR DIMMs with the following specifications:

Maximum RAM

: 2GB (1GB module in each slot)

DIMM Transfer Rates

: 400MHz, 333MHz

Содержание ROCKY-6614













































































































































































































Результаты поиска

Содержание ROCKY-6614

Отзывы:

Похожие инструкции для ROCKY-6614

Бренды по названию

Популярные бренды

IEI Technology ROCKY-6614, Руководство пользователя

Результаты поиска

Содержание ROCKY-6614

Отзывы:

Похожие инструкции для ROCKY-6614

Бренды по названию

Популярные бренды