manualshive.com logo in svg

IDT Tsi620, Руководство пользователя, Страница: 18 / 55

Поделиться
Скачать
IDT Tsi620 Скачать руководство пользователя страница 18

18

Tsi620 Evaluation Board User Manual
60D7000_MA001_03

Intergrated Device Technology

www.idt.com

1.3.2.2

RIO XGMII Interface

•

Up to 12-Gb bandwidth of data transfer between FPGA and sRIO switch

•

Reference clock: RX_CLK from Tsi620 

•

Frequency: 62.5, 125, or 156.25 MHz (Note: Revision 1 of the Tsi620 evaluation board does not 
support 156.25 MHz. 

•

Tx_CLK: sync with Rx-CLK and must be PLL locked before driving out

•

Signaling: HSTL-1.5V Class-II

•

Termination: FPGA on-die parallel 50-ohm termination for the receiver and on-die 25 ohm serial 
termination for the transmitter

•

Protocol: RapidIO for logical and transport layers 

•

Rx: 38 signals

•

Tx: 38 signals 

1.3.2.3

RF Antenna Interface

•

Compliant specifications: CPRI specification v2.1, OBSAI v2.0, OBSAI RP3 v4.0

•

Supports 1x link to SFP connector with OBSAI-768 Mb or CPRI-614.4 Mb 

•

Supports 4x link to DSP with OBSAI-768 Mb or CPRI-614.4 Mb

•

Clocking Source: FPGA local PLL with reference clock at 30.72 MHz and LVDS/LVPECL logic

1.3.2.4

OBSAI System Clock an Synchronization 

•

Compliant specifications: OBSAI RP1 standard

•

Source mode: AMC backplane or SMA connectors 

•

System clock input: 30.72 MHz with LVDS/LVPECL logic standard

•

Frame synchronization burst input: 3.84 MHz with LVTTL logic

•

FPGA outputs the system synchronization signals to the DSP Frame Sync Module (FSM)

1.3.2.5

EMAC 100BaseT Port

•

10Mb/100Mb BaseT with MII interface

•

External PHY to RJ45 connector

1.3.2.6

FPGA Testing Support

•

2-digit LED display

•

One Mictor connector 

•

One 2-bit DIP switch

Содержание Tsi620
























































Отзывы:

Нет отзывов