IBM SAN384B Скачать руководство пользователя страница 112 | Manualshive

Страница: 112 / 183

background image

Removing and installing inter-chassis link (ICL) cables

Note:

ICL ports can be used only with an ICL license. After the addition or
removal of a license, the license enforcement is performed on the ICL ports
only when the

portDisable

and

portEnable

commands are issued on the

ports. An ICL license must be installed on all systems forming the ICL
connection. The systems can be any combination of up to three SAN384B
and SAN768B chassis.

Attention:

If ICL cables are not in use, the ports must have EMI plugs installed to

meet EMI and other regulatory certifications.

Table 17 describes the ICL connector port LED patterns and the recommended
actions for those patterns.

Table 17. ICL connector port LEDs

LED purpose

Color

Status

Recommended
action

LINK LED

No light (LED is off)

No ICL, or ICL cable
present but no
connection.

Ensure that the ICL
cable is correctly
installed.

Steady green

ICL connected.

No action required.

ATTN LED

No light (LED is off)

ICL operational.

No action required.

Blinking amber

Attention required.

Ensure that the ICL
cable is correctly
installed.

Follow this procedure to remove and install the ICL cables. Refer to the

Fabric OS

Administrator’s Guide

for the configuration procedure and requirements.

Figure 44 on page 85 shows the two ends of an ICL cable. The ICL cables (2 meters
long) and the ICL connectors are color-coded and labeled for ease of installation.
The cables can connect ICL connector ports on the SAN384B core switch blades
(CR4S-8) or SAN768B core switch blades (CR8).

84

SAN384B Installation, Service, and User Guide

«
...
110
111
112
113
114
...
»

Содержание SAN384B
























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SAN384B

Z-DRIVE R2 E88 512GB PCI-EXPRESS X8 SSD

Бренд: OCZ Страницы: 2

Бренд: US Robotics Страницы: 156

Бренд: U-Line Страницы: 3

Бренд: POCKetec Страницы: 19

Cloud Object Storage System Slicestor 2212...

Бренд: IBM Страницы: 50

StoreVirtual 3200

Бренд: HPE Страницы: 54

Бренд: HOMEDEPOT Страницы: 24

Бренд: Thunderbolt Страницы: 37

Expansion STEB6000403

Бренд: Seagate Страницы: 5

Бренд: Infrant Technologies Страницы: 2

Бренд: Infrant Technologies Страницы: 8

Бренд: Cavalry Страницы: 16

Бренд: Cavalry Страницы: 16

CADA-C32A Series

Бренд: Cavalry Страницы: 18

Бренд: Fujitsu Страницы: 12

Бренд: Fujitsu Страницы: 16

Бренд: Fujitsu Страницы: 201

Бренд: Fujitsu Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды