IBM SAN384B Скачать руководство пользователя страница 71 | Manualshive

Страница: 71 / 183

background image

Verifying correct operation and backing up the configuration

To verify correct operation and to back up the system, follow these steps.

1.

Check the LEDs to verify that all components are functional. For information
about LED patterns, see Chapter 4, “Monitoring system components,” on page
45.

2.

If necessary, log on to the switch by Telnet, using the

admin

account.

3.

Verify the correct operation of the system by entering the

switchShow

command from the workstation. This command provides information about
switch and port status.

4.

Verify the correct operation of the SAN384B in the fabric by entering the

fabricShow

command from the workstation. This command provides general

information about the fabric.

5.

To back up the configuration, run the following two steps:

a.

Enter the

configupload -vf

command. This command uploads the system

virtual fabric data.

b.

Enter the

configupload

command. This command uploads the system

configuration.

6.

Run the following commands to see additional configuration information that
you can then copy to a file to save:

v

configShow

v

ipAddrShow

v

licenseShow

v

switchShow

Note:

Passwords are not saved in the configuration file, and are not uploaded
during a

configUpload

. Password information should be saved in hardcopy

in a secure location for reference, subject to your security and password
management policy.

Note:

It is recommended that the configuration be backed up on a regular basis to
ensure that a complete configuration is available for downloading to a
replacement device.

Fabric OS firmware updates

To ensure optimum functioning of your system, IBM recommends operating your
system with the latest Fabric OS version and firmware updates. Refer to the latest
Fabric OS Release Notes and Interoperability Matrix for information regarding
Fabric OS compatibility. This is particularly important for fabrics with 1-Gbps
switches using earlier Fabric OS versions. Detailed information on downloading
and installing firmware are provided in the

Fabric OS Administrator's Guide

.

To access the appropriate matrix:

v

Go to the IBM SAN web page www.ibm.com/systems/storage/san

v

Select the SAN384B product link

v

On the SAN384B product page, click the

Interoperability Matrix

link.

Firmware release notes and download files are available through the IBM SAN
Support web pages.

To view release notes and to download firmware:

Chapter 3. Starting and configuring the SAN384B

43

|

|
|

|
|

|
|

«
...
69
70
71
72
73
...
»

Содержание SAN384B
























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SAN384B

Бренд: Unior Страницы: 2

XCubeNAS XN7012R

Бренд: Qsan Страницы: 16

Бренд: National Instruments Страницы: 5

Бренд: SanDisk Страницы: 2

Бренд: IBM Страницы: 34

RS-1600-FC-FFX2

Бренд: Xyratex Страницы: 82

Mobileraid MR8X

Бренд: Sans Digital Страницы: 81

Бренд: kioxia Страницы: 24

USO-HA D500 Series

Бренд: STONEFLY Страницы: 58

Бренд: iodd Страницы: 16

Freiburg 42978909

Бренд: Profiwerk Страницы: 10

Бренд: Vivo Страницы: 3

TRANSMEMORY U2M-004GT

Бренд: Toshiba Страницы: 26

Бренд: Toshiba Страницы: 32

Бренд: Femi Страницы: 60

Бренд: ENHANCE TECHNOLOGY Страницы: 6

Бренд: G-Technology Страницы: 33

Бренд: Alpha ESS Страницы: 58

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды