manualshive.com logo in svg

IBM Power 720 Express, Обзор

IBM Power 720 Express - Мощный сервер для вашего бизнеса. Скачайте бесплатно руководство по установке и эксплуатации нашего продукта с нашего {веб-сайта}. Идеальный выбор для вашего предприятия.

Поделиться
Скачать
background image

140

 

IBM Power 720 and 740  Technical Overview and Introduction

System requirements for source and destination

The source partition must be one that has only virtual devices. If there are any physical 
devices in its allocation, they must be removed before the validation or migration is initiated. 
An N_Port ID Virtualization (NPIV) device is considered virtual and is compatible with 
partition migration.

The hypervisor must support the Partition Mobility functionality (also called migration process) 
that is available on POWER6, , POWER7 and processor-based 
hypervisors. Firmware must be at firmware level eFW3.2 or later. All  
processor-based hypervisors support Live Partition Mobility. Source and destination systems 
can have separate firmware levels, but they must be compatible with each other.

A possibility is to migrate partitions back and forth between POWER6, , POWER7 
and  processor-based servers. Partition Mobility uses the POWER6 or  
Compatibility Modes that are provided by POWER7 and  processor-based servers. 
On the  processor-based server, the migrated partition is then executing in 
POWER6 or  Compatibility Mode.

If you want to move an active logical partition from a POWER6 processor-based server to a 
processor-based server so that the logical partition can take advantage of the 
additional capabilities available with the  processor, use the following steps:

1. Set the partition-preferred processor compatibility mode to the default mode. When you 

activate the logical partition on the POWER6 or processor-based server, it 
runs in the POWER6 or  mode.

2. Move the logical partition to the  processor-based server. Both the current 

and preferred modes remain unchanged for the logical partition until you restart the 
logical partition.

3. Restart the logical partition on the processor-based server. The hypervisor 

evaluates the configuration. Because the preferred mode is set to default and the logical 
partition now runs on a processor-based server, the highest mode available is 
the  mode. The hypervisor determines that the most fully featured mode that is 
supported by the operating environment installed in the logical partition is the POWER7 
mode and changes the current mode of the logical partition to the POWER7 mode. 

Now the current processor compatibility mode of the logical partition is the POWER7 mode, 
and the logical partition run on the  processor-based server.

The Virtual I/O Server on the source system provides the access to the client resources and 
must be identified as a mover service partition (MSP). The Virtual Asynchronous Services 
Interface (VASI) device allows the mover service partition to communicate with the hypervisor. 
It is created and managed automatically by the managed console and will be configured on 
both the source and destination Virtual I/O Servers, which are designated as the mover 
service partitions for the mobile partition, to participate in active mobility. Other requirements 
include a similar time-of-day on each server, systems must not be running on battery power, 

Support of both processors: Because POWER7 and  use the same 
Instruction Set Architecture (ISA), they are equivalent regarding partition mobility, that is 
POWER7 Compatibility Mode supports both POWER7 and  processors.

Tip: The following web page offers presentations of the supported migrations:

http://pic.dhe.ibm.com/infocenter/powersys/v3r1m5/index.jsp?topic=/p7hc3/iphc3p
cmcombosact.htm

Содержание Power 720 Express















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Power 720 Express

Fein FMM350Q Manual preview
FMM350Q
Бренд: Fein Страницы: 43
Fein AFSC18Q Original Instructions Manual preview
AFSC18Q
Бренд: Fein Страницы: 166
TREND CRT/MK3 Original Instructions Manual preview
CRT/MK3
Бренд: TREND Страницы: 32
Steren CAU-35 Instruction Manual preview
CAU-35
Бренд: Steren Страницы: 2
Omer 90.38 CLD2-3 Use, Maintenance And Spare Parts Manual preview
90.38 CLD2-3
Бренд: Omer Страницы: 2
KEPCO HSF 24-50A Operator'S Manual preview
HSF 24-50A
Бренд: KEPCO Страницы: 12
El-Björn Alfa-II Instruction preview
Alfa-II
Бренд: El-Björn Страницы: 2
TekPower TP-3003D User Manual preview
TP-3003D
Бренд: TekPower Страницы: 4
Rapid Airtac PBS121 Operating Instructions Manual preview
Airtac PBS121
Бренд: Rapid Страницы: 87
Parkside PBSG 95 E6 Translation Of The Original Instructions preview
PBSG 95 E6
Бренд: Parkside Страницы: 96
Sima ATA 450 Li-ion User Manual preview
ATA 450 Li-ion
Бренд: Sima Страницы: 15
SFORZATO DSP-030EX User Manual preview
DSP-030EX
Бренд: SFORZATO Страницы: 9
Sealey SMART ERASER SA695 Instructions preview
SMART ERASER SA695
Бренд: Sealey Страницы: 4
Ametek Powervar 3400 Series User Manual preview
Powervar 3400 Series
Бренд: Ametek Страницы: 68
ASTRO TOOL Corp. 10692 Manual preview
10692
Бренд: ASTRO TOOL Corp. Страницы: 2
Zato CAYMAN FCE II Series Safety, Operation And Maintenance Manual preview
CAYMAN FCE II Series
Бренд: Zato Страницы: 96
Lampo IP30 User Manual preview
IP30
Бренд: Lampo Страницы: 19
Zendure ZenY Pro Cable User Manual preview
ZenY Pro Cable
Бренд: Zendure Страницы: 32

Бренды по названию

Популярные бренды

Загрузить еще бренды