i3 International S81 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 205

background image

13

Power ON/OFF Device

To power on this device, simply plug it into the wall. To power down the switch simply unplug the switch from it is power
cord.

Installing Equipment

You can mount this device into a standard 19-inch equipment rack. You can center- or front-mount the device in a rack.
Optional rack-mounting brackets are supplied with the device. Otherwise the devise can be placed on a flat shelf with the
adhesive feet applied to the bottom of the device.

Network Connections

1000Base-T Ports

The switch contains 8 1000BASE-T RJ45 ports. All RJ45 ports support automatic MDI/MDI-X operation, auto-negotiation
and IEEE 802.3x auto-negotiation of flow control, so the optimum data rate and transmission can be selected
automatically.

SFP Transceiver Slots

The S81 supports 2 Small Form Factor Pluggable (SFP)

transceiver. In the default configuration, if an SFP transceiver

(purchased separately) is installed in a slot and has a valid link on the port, the associated RJ45 port is disabled. The
following table shows a list of transceiver types which have been tested with the switch. Please contact i3 International
Tech Support if you have any questions with the SFP transceivers.

The SFP slots support the following optional SFP Transceiver Types
SFP.LC

1000Base-SX GE SFP Fiber Module, LC Multi-Mode 850nm

SFP.LCM2

1000Base-SX GE SFP Fiber Module, LC Multi-Mode 1310nm 2km

SFP.LC.S10

1000Base-SX GE SFP Fiber Module, LC Single-Mode 10km

SFP.LC.S30

1000Base-SX GE SFP Fiber Module, LC Single-Mode 30km

SFP.LC.S50

1000Base-SX GE SFP Fiber Module, LC Single-Mode 50km

SFP.L5.S50

1000Base-SX GE SFP Fiber Module, LC Single-Mode 50km

SFP.BL5.S10

1000Base-LX GE SFP Fiber Module, Bidi LC Single-Mode 10km, 1310nm

SFP.BL3.S10

1000Base-LX GE SFP Fiber Module, Bidi LC Single-Mode 10km, 1550nm

SFP.BL5.S20

1000Base-LX GE SFP Fiber Module, Bidi LC Single-Mode 20km

SFP.BL3.S20

1000Base_LX GE SFP Fiber Module, Bidi LC Single Mode 20km, 1310nm

SFP.FLC

100Base-FX FE SFP Fiber Module, LC Multi-Mode

SFP.FLC.S20

100Base-FX FE SFP Fiber Module, LC Single-Mode 20km

Installing an Optional SFP Transceiver

It is possible to install or remove a mini-GBIC SF from a mini-GBIC slot without having to power off the switch. The mini-
GBIC slots are shared with the two 10/ 100/ 1000Base-T RJ-45 ports. If a mini-GBIC is installed in a slot, the associated
RJ45 port is disabled and cannot be used and operate only at full duplex. Half duplex operation is not supported. Ensure

«
...
12
13
14
15
16
...
»

Содержание S81














































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для S81

Бренд: H3C Страницы: 38

Бренд: H3C Страницы: 36

Бренд: H3C Страницы: 9

Бренд: H3C Страницы: 36

S12500X-AF Series

Бренд: H3C Страницы: 21

S12500X-AF Series

Бренд: H3C Страницы: 42

Бренд: H3C Страницы: 16

Бренд: H-Tronic Страницы: 32

Бренд: Broadcast Tools Страницы: 28

Бренд: Teseq Страницы: 60

Бренд: SMC Networks Страницы: 43

MatrixPRO 8x8 DVI

Бренд: Barco Страницы: 2

AVS-OCT-6448-210

Бренд: AMX Страницы: 1

CT.TS005.501401

Бренд: Talkswitch Страницы: 9

Бренд: Eaton Страницы: 3

Бренд: LevelOne Страницы: 40

Бренд: I/O Interconnect Страницы: 27

Бренд: Gembird Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды