HydraMaster BoxxerXL Скачать руководство пользователя страница 29

Страница: 29 / 144

2-3: Installation Information

Use caution when drilling any holes through the van floor. Many vans have critical

components mounted directly below the vehicle floor that could be damaged by

a misplaced drill bit.

LOCatIng tHe BOXXer XL In VeHICLe

There are two recommended entry points on the vehicle for the Boxxer XL installation: the

side door or the rear doors.

Most installations are through the side door. This provides rear access for accessories

and hoses as well as unobstructed access to the component/working side of the machine,

thus making it a bit easier to perform maintenance and/or repair without removing the unit

from the truck.

Rear mounting requires the unit to be slid to the right side as far as possible Although

installing the Boxxer XL through the rear door partly limits working access, it does direct

the noise away from the cleaning site.

In addition, rear mounting not only provides adequate working space on the component

side of the unit but also improves weight distribution inside the van (engine and component

weight line up over drive shaft). Some cleaners in colder geographical areas prefer this

placement for better traction in ice and snow. Also, it is physically easier to load the unit

into the rear door due to the height of the vehicle bed.

Secure Installation

No matter how the unit is installed, check to see if the Boxxer XL is properly secured to

the floor of the van with the hardware provided. This safety measure will ensure that the

machine will not slide inside the van. See figure 2-2 for the correct installation.

figure 2-2. recommended Location of Boxxer XL in Van

Содержание BoxxerXL

















































































































































Результаты поиска

Содержание BoxxerXL

Отзывы:

Похожие инструкции для BoxxerXL

Бренды по названию

Популярные бренды

HydraMaster BoxxerXL, Руководство пользователя

Результаты поиска

Содержание BoxxerXL

Отзывы:

Похожие инструкции для BoxxerXL

Бренды по названию

Популярные бренды