HydraMaster BoxxerXL Скачать руководство пользователя

Страница: 142 / 144

Warranty Information: 11-2

VaCUUM anD SOLUtIOn HOSeS

• failure to protect hoses against freezing.

• failure to protect hoses against burns from engine and blower exhaust.

• Damage to hoses from being run over by vehicles.

• Kinking or cracking from failure to store or unroll hoses correctly.

• Normal wear and tear from everyday use.

CLeanIng WanD anD tOOL

• failure to protect against freezing.

• Obvious physical abuse of wand or tool.

Water HeatIng SySteM

• Over-pressurization of the system (recommended maximum working pressure -

1,200 psi)

• failure to protect against freezing.

HarD Water DepOSItS

• failure to use or maintain a water softening system or a properly installed magnetic-

type descaler, whichever might be necessary, with machines operating in designated

“Hard Water Areas” (3.0 grains or more per gallon).

Warranty prOCeDUre

Warranty coverage is available to you through your local distributor. Please refer to

the Golden Guarantee© Limited Warranty document shipped to you with the Owner’s

Guide.

If you have moved to a new area or have purchased a used machine and need information

regarding your local distributor, call HydraMaster at (425) 775-7272 or email us at:

[email protected].

When calling your distributor, be sure to have the machine’s information; model and serial

number, ready for the service representative.

Содержание BoxxerXL

















































































































































Результаты поиска

Содержание BoxxerXL

Отзывы:

Похожие инструкции для BoxxerXL

Бренды по названию

Популярные бренды

HydraMaster BoxxerXL, Руководство пользователя

Результаты поиска

Содержание BoxxerXL

Отзывы:

Похожие инструкции для BoxxerXL

Бренды по названию

Популярные бренды