HydraMaster BoxxerXL Скачать руководство пользователя страница 87

Страница: 87 / 144

8-9: Systems Troubleshooting

VaCUUM SySteM

1. Weak vacuum at wand. the gauge reads normal.

possible Cause

Solution

1.1. Blockage in the

hoses or wand tube

Disconnect the hoses and check for an obstruction.

1.2. excessive length of

hose connected to the

truckmount

Do not attach excessive lengths of hose.

2. Weak vacuum

possible Cause

Solution

2.1. Air leak somewhere

in the vacuum system

Check the vacuum relief valve for proper adjustment.

Carefully check all the vacuum hoses for a cut or break.
Check the recovery tank lid gasket.
Make sure the recovery tank drain valve is fully closed.

2.2. The vacuum blower

is turning too slowly.

Check the rpm of the engine. Adjust as necessary to

3,000 rpm under a 12" Hg. vacuum load.

2.3. The vacuum gauge is

defective.

Test the gauge and replace if necessary.

3. the vacuum gauge reads too high with no hoses attached

possible Cause

Solution

3.1. The filter in recovery

tank is clogged.

Remove and clean or replace as necessary.

3.2. The hose from

recovery tank to the

vacuum blower is

collapsed internally.

Inspect and replace as necessary.

4. excessive noise produced by the blower

possible Cause

Solution

4.1. The blower is low on

oil.

Inspect the oil levels and replenish as necessary. Note:

Running the blower with low oil levels can cause severe

damage. If this situation occurs the blower should be

inspected by a qualified service technician.

4.2. The vacuum blower

has internal damage.

Refer to a qualified service technician.

Содержание BoxxerXL

















































































































































Результаты поиска

Содержание BoxxerXL

Отзывы:

Похожие инструкции для BoxxerXL

Бренды по названию

Популярные бренды

HydraMaster BoxxerXL, Руководство пользователя

Результаты поиска

Содержание BoxxerXL

Отзывы:

Похожие инструкции для BoxxerXL

Бренды по названию

Популярные бренды