HydraMaster BoxxerXL Скачать руководство пользователя

Страница: 51 / 144

5-5: Machine Maintenance

engIne MaIntenanCe

engine Oil Level Check

The engine oil level should be checked daily. It is recommended that the oil be checked

just before the engine is started for the first time for that day. The oil level should be

between the ‘Add’ and the ‘full’ marks on the dipstick.

Do not operate the engine with the oil level below the bottom of the ‘Add’ mark on

the dipstick, or above the top of the ‘full’ mark.

adding engine Oil

It is normal to add some oil in the period of time between oil changes. The amount will

vary with the severity of operation. When adding or replacing engine oil, be sure the oil

meets or exceeds the recommended specification.

Changing engine Oil and filter

The engine oil and filter must be changed every 50 hours or every 6 weeks whichever

occurs first. The oil and filter should be changed more often if the engine is operating in

dusty or extremely dirty areas, or during cold weather.

engine Oil Quality

To achieve proper engine performance and durability, it is important that you use only

engine lubricating oils of the correct quality in your engine. Proper quality oils also provide

maximum efficiency for crankcase ventilation systems, which reduces pollution.

use only engine oils displaying the American Petroleum Institute (API) “starburst”

certification mark ‘FOR GASOLINE ENGINES’ on the container.

engine Oil Recommendation

While multi-viscosity oils are generally recommended, 5W-30 synthetic is specifically

recommended year round for your Boxxer XL engine.

Содержание BoxxerXL

















































































































































Результаты поиска

Содержание BoxxerXL

Отзывы:

Похожие инструкции для BoxxerXL

Бренды по названию

Популярные бренды

HydraMaster BoxxerXL, Руководство пользователя

Результаты поиска

Содержание BoxxerXL

Отзывы:

Похожие инструкции для BoxxerXL

Бренды по названию

Популярные бренды