HydraMaster BoxxerXL Скачать руководство пользователя страница 82

Страница: 82 / 144

Systems Troubleshooting: 8-4

engIne

1. the engine will not turn over

possible Cause

Solution

1.1. A loose or corroded

battery terminal.

Clean and tighten the battery terminal connections.

1.2. The battery is dead. Recharge or replace the battery. Test the charging system.

Repair if necessary.

Do not attempt to jump start the truckmount from

a running vehicle. The amperage output from an

automobile will damage the charging system of the

truckmount.

1.3. The main fuse is

blown.

Check the main fuse.

If the fuse is blown, inspect the electrical system for worn

or shorted wires. Repair or replace as necessary.

1.4. The vacuum blower

has seized.

Attempt to turn the coupler by hand. If it will not turn refer

to the Vacuum System Troubleshooting Subsection (page

8-9).

1.5. The ignition switch is

faulty.

Test to see if there is power both to and from the switch.

Refer to the electrical Section of this manual (page 7-1).

1.6. The starter solenoid

is faulty.

Test to see if there is power to solenoid with ignition in

"START" position. Refer to electrical Section (page 7-1).

1.7. The starter motor is

faulty.

Test to see if there is power to the motor with the ignition

in "START" position. Refer to the electrical Section (page

7-1)..

1.8. None of the above.

Refer to a qualified service technician for further

troubleshooting.

Содержание BoxxerXL

















































































































































Результаты поиска

Содержание BoxxerXL

Отзывы:

Бренды по названию

Популярные бренды

HydraMaster BoxxerXL, Руководство пользователя

Результаты поиска

Содержание BoxxerXL

Отзывы:

Бренды по названию

Популярные бренды