HydraMaster BoxxerXL Скачать руководство пользователя страница 49

Страница: 49 / 144

5-3: Machine Maintenance

250 Hours

• Check the engine valve clearance (intake and exhaust 0.004” - 0.006” [0.101 mm

- 0.152 mm]).

• Check coupler element for cracks or wear. Replace as necessary.

400 Hours

•

Change fuel filter.

500 Hours

•  Change the blower oil.
•  Change the high pressure pump oil.
•  Check coupler element for cracks or wear. Replace as necessary.
•  Replace spark plugs.

1,000 Hours

• Replace spark plugs.
•

Change air filters.

•  Check carburetor. Clean or replace as necessary.
•  Replace coupler element.
•  Clean heat exchanger core.

Refer to the Interval in Hours Maintenance chart in the Owner’s Guide for more

information.

Содержание BoxxerXL

















































































































































Результаты поиска

Содержание BoxxerXL

Отзывы:

Похожие инструкции для BoxxerXL

Бренды по названию

Популярные бренды

HydraMaster BoxxerXL, Руководство пользователя

Результаты поиска

Содержание BoxxerXL

Отзывы:

Похожие инструкции для BoxxerXL

Бренды по названию

Популярные бренды