HydraMaster BoxxerXL Скачать руководство пользователя страница 40

Страница: 40 / 144

Cleaning Information: 3-8

Upholstery tool: DriMaster

use the upholstery tool on small rugs and furniture. When you clean rugs, be sure that the

temperature and chemicals are safe for that particular type of rug.

As with the larger tools, do not leave the surface of the upholstery too wet. Adjust the

volume of water on the tool without it touching any surface: the water should just barely

come out of the tool before the vacuum pulls it back in. The water will only just spray the

top layer of the furniture and the vacuum will pull the dirty water back into the tool.

If you find it necessary to do a dry pass, keep strokes short to limit the amount of water

that comes into contact with the fabric surface.

for more information about HydraMaster accessories, please visit this web page:

http://hydramaster.com/Products/Accessories.aspx

Upholstery Tool

Part #000-163-012

Grip

Part #000-061-144

Содержание BoxxerXL

















































































































































Результаты поиска

Содержание BoxxerXL

Отзывы:

Бренды по названию

Популярные бренды

HydraMaster BoxxerXL, Руководство пользователя

Результаты поиска

Содержание BoxxerXL

Отзывы:

Бренды по названию

Популярные бренды