HydraMaster BoxxerXL Скачать руководство пользователя страница 28

Страница: 28 / 144

Installation Information: 2-2

OperatIng tHe BOXXer XL In HOt WeatHer

HydraMaster recommends the following steps when operating the Boxxer XL during

periods of hot weather (95º f [35º C] or higher). This will help ensure that your Boxxer XL

continues to run at 100% capacity during even the hottest days.

1. A minimum of 9” (22.9 cm) of clearance is required on both sides of the Boxxer XL,

when installed. ensure that additional equipment or other materials are not stored at

the sides or on top of the Boxxer XL. Unobstructed airflow around the unit is critical

for cooling the engine and other components.

2. for side-door vans with “barn doors”, open the doors as wide as their construction

will allow. Be sure to open the doors beyond their standard “straight-out” position,
if possible, by releasing the stops and putting the doors in their fully extended
position.

3. Provide cross-ventilation. When possible, keeping the rear doors open while the

Boxxer XL is running will substantially reduce the temperature inside the van and

will provide a path for cooling air flow. For rear-mount installations, open up the

other doors in the van.

4. Consider adding powered roof vents to the vehicle (if not already installed). These

vents can significantly reduce interior temperatures and will result in much cooler

operation. A powered roof vent is required when the Boxxer XL is mounted on the
optional 85 Gallon fresh Water Tank.

Содержание BoxxerXL

















































































































































Результаты поиска

Содержание BoxxerXL

Отзывы:

Похожие инструкции для BoxxerXL

Бренды по названию

Популярные бренды

HydraMaster BoxxerXL, Руководство пользователя

Результаты поиска

Содержание BoxxerXL

Отзывы:

Похожие инструкции для BoxxerXL

Бренды по названию

Популярные бренды