HydraMaster BoxxerXL Скачать руководство пользователя | Manualshive

Страница: 17 / 144

background image

1-9: General Information

reSpOnSIBILItIeS

purchaser’s responsibilities

• Prior to purchasing a van, ensure that the payload is suitable for all of the equipment

that will be installed and transported. This includes and is not limited to: the truckmount,
recovery tanks, fresh water tanks, on-board water, hose reels, hoses, cleaning tools,
chemicals and drying equipment. Payload capacity information is available through
the auto dealer, the manufacturer’s web site, and is also located on the door pillar of
the driver’s side door.

• Purchase a heavy duty Group 24 (500+ CC Amps) battery for this truckmount. This is

normally available from the installation dealer.

• Prior to dropping your van off at the distributor for the truckmount to be installed, have

a spray-on bed liner applied to the floor such as Rhino Lining® or Line-X®.

Plywood and carpet are not recommended.

• Prior to operating the truckmount, read this manual in its entirety and familiarize

yourself with the information contained here. Special attention should be paid to all

Warnings and Cautions

.

• The distributor is responsible for the correct installation of the truckmount. The

distributor is also responsible to train you in the correct and proper operation and
maintenance of the truckmount.

Any modification of the truckmount may void the warranty.

«
...
15
16
17
18
19
...
»

Содержание BoxxerXL

















































































































































Отзывы:

Нет отзывов

Похожие инструкции для BoxxerXL

Бренд: GE Страницы: 28

Бренд: Zehnder Pumpen Страницы: 24

Бренд: Bartec Страницы: 46

Бренд: Panasonic Страницы: 132

Бренд: Panasonic Страницы: 10

Бренд: AARU ENGINEERS Страницы: 4

Бренд: Davey Страницы: 16

Бренд: SAER Elettropompe Страницы: 72

Бренд: National Instruments Страницы: 13

Бренд: National Instruments Страницы: 30

Бренд: Navien Страницы: 48

Бренд: Navien Страницы: 2

Бренд: Valcom Страницы: 4

Бренд: Yaesu Страницы: 2

ACUSTICA H series

Бренд: RCF Страницы: 10

STExB2X05-S Series

Бренд: E2S Страницы: 20

RJS-75SS Series

Бренд: red lion Страницы: 32

Бренд: usi Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды