Hussmann PCS Скачать руководство пользователя страница 36

Страница: 36 / 54

Protocol

Control

System

Users

Manual

2/12/01

Table 49- PSC Configuration Screen 5 Fields

Field

Explanation

Winter On

If the ambient temperature
is below this setpoint, the
spray pump will not be
turned on

Winter Off

If the ambient temperature
is above this setpoint, the
spray pump can be turned
on

Override On

If the outlet temperature is
above this setpoint, the
spray pump will be
enabled regardless of the
ambient temperature. Note
that if the outlet
temperature goes above
this setpoint, a High Temp
Alarm will be activated.

Override Off

If the outlet temperature is
below this setpoint, the
spray pump will be
disabled if the ambient
temperature is below the
Winter On setpoint

Figure 81- PSC Configuration Screen 6

Table 50- PSC Configuration Screen 6 Fields

Field

Explanation

Minimum PSI

Low Pressure setpoint for
the water pressure. If the
pressure is below this
value for the delay time, an
alarm will be activated.

Maximum PSI

High Pressure setpoint for
the water pressure. If the
pressure is above this
value for the delay time, an
alarm will be activated.

Alarm Delay

Delay time before
activating pressure alarm

Figure 82- PSC Configuration Screen 7

Table 51- PSC Configuration Screen 7 Fields

Field

Explanation

Max Range

Maximum range of the
pressure probe. Should
always be 362 PSI.

Min Range

Minimum range of the
pressure probe. Should
always be 0 PSI.

Offset

Offset of the pressure
probe

Figure 83- PSC Configuration Screen 8

Table 52- PSC Configuration Screen 8 Fields

Field

Explanation

Pump 1

Initial value for run time
value for Pump 1 (hours)

Pump 2

Initial value for run time
value for Pump 2 (hours)

Pump Interval

Time interval to switch
between pumps (hours)

Figure 84- PSC Configuration Screen 9

Table 53- PSC Configuration Screen 9 Fields

Field

Explanation

Time

Used to set the time of the
controller

Date

Used to set the date of the
controller

Day

Used to set the day of the
controller

Page 36

Содержание PCS























































Результаты поиска

Содержание PCS

Отзывы:

Похожие инструкции для PCS

Бренды по названию

Популярные бренды

Hussmann PCS, Руководство пользователя

Результаты поиска

Содержание PCS

Отзывы:

Похожие инструкции для PCS

Бренды по названию

Популярные бренды