Huawei UPS2000-G-1KRTL Скачать руководство пользователя страница 48

Страница: 48 / 78

UPS2000-G-(1 kVA-3 kVA)
User Manual

4 Setting Control Panel

Issue 08 (2017-08-04)

Huawei Proprietary and Confidential

Alar
m ID

Alar
m
Cause
ID

Alar
m
Name

Alarm
Severity

Alarm Clear
Mode

Trigger
Condition

Impact on
the System

Repair Proposal

replace batteries.

Interna
l
overte
mperat
ure

Minor

This alarm is
automatically
cleared.

The ambient
temperature
exceeds 50º

The UPS
remains in
the current
state and
cannot start.

Possible cause: The
ambient
temperature
exceeds 50º

C when

the UPS is in
standby mode. As a
result, the UPS
cannot start.

Measure: Lower the
ambient
temperature at
which the UPS
works.

Interna
l fault

Critical

This alarm
must be
manually
cleared.

The bus
voltage is
lower than
320 V.

This alarm is
generated
during the
startup of
the UPS. If
this alarm is
generated,
the UPS
fails to start.

Possible cause: The
soft-start resistor is
damaged.

Measure: Contact
the dealer or
Huawei technical
support for repair.

Interna
l fault

Critical

This alarm
must be
manually
cleared.

The bus
voltage is
higher than
450 V.

If this alarm
is generated
during the
running of
the UPS, the
UPS
transfers to
bypass
mode.



Possible cause:
The mains has
experienced a
transient high
voltage.
Measure:
Rectify the fault
and restart the
UPS.



Possible cause:
The output
supplies power
to special loads
such as the
inductive and
rectification
loads.

Measure: Check
that the load
types are
supported by the
UPS.



Possible cause:
The hardware is

Содержание UPS2000-G-1KRTL















































































Результаты поиска

Содержание UPS2000-G-1KRTL

Отзывы:

Похожие инструкции для UPS2000-G-1KRTL

Бренды по названию

Популярные бренды

Huawei UPS2000-G-1KRTL, Руководство пользователя

Результаты поиска

Содержание UPS2000-G-1KRTL

Отзывы:

Похожие инструкции для UPS2000-G-1KRTL

Бренды по названию

Популярные бренды