Huawei UPS2000-G-1KRTL Скачать руководство пользователя страница 49

Страница: 49 / 78

UPS2000-G-(1 kVA-3 kVA)
User Manual

4 Setting Control Panel

Issue 08 (2017-08-04)

Huawei Proprietary and Confidential

Alar
m ID

Alar
m
Cause
ID

Alar
m
Name

Alarm
Severity

Alarm Clear
Mode

Trigger
Condition

Impact on
the System

Repair Proposal

damaged.

Measure:
Contact the
dealer or
Huawei
technical
support.

Interna
l fault

Critical

This alarm
must be
manually
cleared.

The bus
voltage is
lower than
260 V.

If this alarm
is generated
during the
running of
the UPS, the
UPS
transfers to
bypass
mode.



Possible cause:
The hardware is
damaged.

Measure:
Contact the
dealer or
technical
support.



Possible cause:
An overload
occurred when
the input voltage
was low.

Measure:
Rectify the fault
and restart the
UPS.

Interna
l fault

Minor

This alarm is
automatically
cleared.

An error
occurs in the
EEPROM.

All UPS
parameters
are restored
to the
factory
settings. If
this alarm is
generated,
the customer
needs to
replace the
UPS.

Possible cause: The
EEPROM is faulty.

Measure: Contact
the dealer or
Huawei technical
support.

Interna
l fault

Critical

This alarm
must be
manually
cleared.

The inverter
voltage is
higher than
1.15 times the
rated output
voltage.

If this alarm
is generated
during the
running of
the UPS, the
UPS
transfers to
bypass
mode.

Possible cause: The
inverter is faulty.

Measure: Contact
the dealer or
Huawei technical
support.

Interna

Critical

This alarm

The inverter

If this alarm

Содержание UPS2000-G-1KRTL















































































Результаты поиска

Содержание UPS2000-G-1KRTL

Отзывы:

Похожие инструкции для UPS2000-G-1KRTL

Бренды по названию

Популярные бренды

Huawei UPS2000-G-1KRTL, Руководство пользователя

Результаты поиска

Содержание UPS2000-G-1KRTL

Отзывы:

Похожие инструкции для UPS2000-G-1KRTL

Бренды по названию

Популярные бренды