HP photosmart 850 Скачать руководство пользователя страница 41

Страница: 41 / 136

Field Description

The Maximum Transmit Unit

MTU of a VLAN interface.

Internet protocol processing :
disabled

The interface is not capable of processing IP packets. This information
is displayed when the interface is not configured with an IP address.

Internet Address is
192.168.1.54/24 Primary

The primary IP address of the interface is 192.168.1.54/24. This
information is displayed only if the primary IP address is configured for

the interface.

Internet Address is 6.4.4.4/24 Sub

The secondary IP address of the interface is 6.4.4.4/24. This
information is displayed only if a secondary IP address is configured

for the interface.

IP Packet Frame Type

IPv4 outgoing frame format.

Hardware address

MAC address corresponding to a VLAN interface.

IPv6 Packet Frame Type

IPv6 outgoing frame format.

Last clearing of counters

Time when the

reset counters interface vlan-interface

command was

last used to clear the interface statistics.

Never

indicates the

reset counters interface vlan-interface

command

has never been used on the interface after the device's startup.

The brief information of interface(s)
under route mode

Brief information about Layer 3 interfaces.

Link: ADM - administratively down;
Stby - standby

Link layer state of an interface:

•

ADM

—The interface has been administratively shut down. To

recover its physical state, perform the

undo shutdown

command.

•

Stby

—The interface is operating as a standby interface. To see the

main interface, use the

display standby state

command.

Protocol: (s) - spoofing

If the network layer protocol state of an interface is shown as UP, but its
link is an on-demand link or not present at all, its protocol attribute
includes the spoofing flag (an s in parentheses).

Interface

Abbreviated interface name.

Link

Physical link state of the interface:

•

—The link is up.

•

ADM

—The link has been administratively shut down. To recover its

physical state, perform the

undo shutdown

command.

Protocol

Protocol connection state of the interface:

•

DOWN

•

UP(s)

Main IP

Main IP address of the interface.

Description

Description of the interface.

Cause

Cause of a DOWN physical link. If the port has been shut down with
the

shutdown

command, this field displays

Administratively

. To restore

the physical state of the interface, use the

undo shutdown

command.

Related commands

reset counters interface vlan-interface

Содержание photosmart 850









































































































































Результаты поиска

Содержание photosmart 850

Отзывы:

Бренды по названию

Популярные бренды

HP photosmart 850, Справочник по командам

Результаты поиска

Содержание photosmart 850

Отзывы:

Бренды по названию

Популярные бренды