HP photosmart 850 Скачать руководство пользователя

Страница: 33 / 136

If you specify the

null

keyword, this command displays information about interface Null 0 with or without

the

keyword, because the device supports only one null interface.

Examples

# Display detailed information about null interface Null 0.

<Sysname> display interface null 0

NULL0 current state :UP

Line protocol current state :UP (spoofing)

Description : NULL0 Interface

The Maximum Transmit Unit is 1500

Internet protocol processing : disabled

Physical is NULL DEV

Last clearing of counters: Never

Last 300 seconds input: 0 bytes/sec, 0 bits/sec, 0 packets/sec

Last 300 seconds output: 0 bytes/sec, 0 bits/sec, 0 packets/sec

0 packets input, 0 bytes, 0 drops

0 packets output, 0 bytes, 0 drops

# Display brief information about interface Null 0.

<Sysname> display interface null 0 brief

The brief information of interface(s) under route mode:

Link: ADM - administratively down; Stby - standby

Protocol: (s) - spoofing

Interface Link Protocol Main IP Description

NULL0 UP UP(s) --

See

Table 5

for the

display interface null

command output.

Related commands

interface null

interface loopback

Use

interface loopback

to create a loopback interface or enter loopback interface view.

Use

undo interface loopback

to remove a loopback interface.

Syntax

interface loopback

interface-number

undo interface loopback

interface-number

Views

System view

Default command level

2: System level

Parameters

interface-number

: Specifies a loopback interface by its number. The loopback interface number is

always 0.

Содержание photosmart 850









































































































































Результаты поиска

Содержание photosmart 850

Отзывы:

Похожие инструкции для photosmart 850

Бренды по названию

Популярные бренды

HP photosmart 850, Справочник по командам

Результаты поиска

Содержание photosmart 850

Отзывы:

Похожие инструкции для photosmart 850

Бренды по названию

Популярные бренды