HP photosmart 850 Скачать руководство пользователя

Страница: 66 / 136

Ten-GigabitEthernet1/0/2 enable

WLAN-ESS1 enable

WLAN-DBSS1:2 enable

Table 12

Command output

Field Description

Mac-address learning status of the switch

Global MAC address learning status (enabled or disabled).

Learning Status

MAC address learning status (enabled or disabled) for an
interface.

display mac-address statistics

Use

display mac-address

statistics

to display the statistics of the MAC address table.

Syntax

display mac-address

statistics

[

{

begin

exclude

include

}

regular-expression

]

Views

Any view

Default command level

1: Monitor level

Parameters

: Filters command output by specifying a regular expression. For more information about regular

expressions, see

Fundamentals Configuration Guide

begin

: Displays the first line that matches the specified regular expression and all lines that follow.

exclude

: Displays all lines that do not match the specified regular expression.

include

: Displays all lines that match the specified regular expression.

regular-expression

: Specifies a regular expression, a case-sensitive string of 1 to 256 characters.

Examples

# Display the statistics of the MAC address table.

<Sysname> display mac-address statistics

MAC TYPE LEARNED USER-DEFINED SYSTEM-DEFINED IN-USE AVAILABLE

Dynamic Unicast 20 0 0 20

Static Unicast 0 0 0 0 8192

Total Unicast 20 8192

Dynamic Multicast 0 0 0 0

Static Multicast 0 0 0 0 0

Total Multicast 0 0

Содержание photosmart 850









































































































































Результаты поиска

Содержание photosmart 850

Отзывы:

Похожие инструкции для photosmart 850

Бренды по названию

Популярные бренды

HP photosmart 850, Справочник по командам

Результаты поиска

Содержание photosmart 850

Отзывы:

Похожие инструкции для photosmart 850

Бренды по названию

Популярные бренды