HP photosmart 850 Скачать руководство пользователя

Страница: 123 / 136

118

<Sysname> system-view

[Sysname] lldp compliance cdp

Related commands

•

lldp hold-multiplier

•

lldp timer tx-interval

lldp enable

Use

lldp enable

to enable LLDP.

Use

undo lldp enable

to disable LLDP.

Syntax

lldp enable
undo lldp enable

Default

LLDP is enabled on a port and disabled globally.

Views

System view, Layer 2 Ethernet interface view, port group view

Default command level

2: System level

Usage guidelines

LLDP takes effect on a port only when LLDP is enabled both globally and on the port.

Examples

# Disable LLDP on Ten-GigabitEthernet 1/0/1.

<Sysname> system-view

[Sysname] interface ten-gigabitethernet1/0/1

[Sysname-Ten-GigabitEthernet1/0/1] undo lldp enable

lldp encapsulation snap

Use

lldp encapsulation

snap

to configure the encapsulation format for LLDP frames as SNAP on a port or

a group of ports.
Use

undo lldp encapsulation

to restore the default encapsulation format for LLDP frames.

Syntax

lldp encapsulation snap
undo lldp encapsulation

Default

Ethernet II is the encapsulation format for LLDP frames.

Views

Layer 2 Ethernet interface view, port group view

Содержание photosmart 850









































































































































Результаты поиска

Содержание photosmart 850

Отзывы:

Похожие инструкции для photosmart 850

Бренды по названию

Популярные бренды

HP photosmart 850, Справочник по командам

Результаты поиска

Содержание photosmart 850

Отзывы:

Похожие инструкции для photosmart 850

Бренды по названию

Популярные бренды