HP photosmart 850 Скачать руководство пользователя

Страница: 127 / 136

122

Default

LLDP trapping is disabled on ports.

Views

Layer 2 Ethernet interface view, port group view

Default command level

2: System level

Examples

# Enable LLDP trapping for Ten-GigabitEthernet 1/0/1.

<Sysname> system-view

[Sysname] interface ten-gigabitethernet1/0/1

[Sysname-Ten-GigabitEthernet1/0/1] lldp notification remote-change enable

lldp timer notification-interval

Use

lldp timer notification-interval

to set the LLDP trap transmission interval.

Use

undo lldp timer notification-interval

to restore the default.

Syntax

lldp timer notification-interval

interval

undo lldp timer notification-interval

Default

The LLDP trap transmission interval is 5 seconds.

Views

System view

Default command level

2: System level

Parameters

interval

: Sets the LLDP trap transmission interval, ranging from 5 to 3600 seconds.

Examples

# Set the LLDP trap transmission interval to 8 seconds.

<Sysname> system-view

[Sysname] lldp timer notification-interval 8

lldp timer reinit-delay

Use

lldp timer reinit-delay

to set the LLDP re-initialization delay.

Use

undo lldp timer reinit-delay

to restore the default.

Syntax

lldp timer reinit-delay

delay

undo lldp timer reinit-delay

Содержание photosmart 850









































































































































Результаты поиска

Содержание photosmart 850

Отзывы:

Похожие инструкции для photosmart 850

Бренды по названию

Популярные бренды

HP photosmart 850, Справочник по командам

Результаты поиска

Содержание photosmart 850

Отзывы:

Похожие инструкции для photosmart 850

Бренды по названию

Популярные бренды