HP photosmart 850 Скачать руководство пользователя страница 129

Страница: 129 / 136

124

lldp timer tx-interval

Use

lldp timer tx-interval

to set the LLDP frame transmission interval.

Use

undo lldp timer tx-interval

to restore the default.

Syntax

lldp timer tx-interval

interval

undo lldp timer tx-interval

Default

The LLDP frame transmission interval is 30 seconds.

Views

System view

Default command level

2: System level

Parameters

interval

: Sets the LLDP frame transmission interval, ranging from 5 to 32768 seconds.

Usage guidelines

It is a good practice to set the LLDP frame transmission interval to be no less than four times the LLDP frame

transmission delay.
If the LLDP frame transmission interval is less than the LLDP frame transmission delay, the device uses the

LLDP frame transmission delay as the transmission interval.

Examples

# Set the LLDP frame transmission interval to 20 seconds.

<Sysname> system-view

[Sysname] lldp timer tx-interval 20

Related commands

lldp timer tx-delay

lldp tlv-enable

Use

lldp tlv-enable

to configure the types of advertisable TLVs for a port or all ports in a port group.

Use

undo lldp tlv-enable

to disable the advertising of the specified types of TLVs.

Syntax

lldp

tlv-enable

{

basic-tlv

{

all

port-description

system-capability

system-description

system-name

} |

dot1-tlv

{

all

port-vlan-id

protocol-vlan-id

[

vlan-id

] |

vlan-name

[

vlan-id

]

} |

dot3-tlv

{

all

link-aggregation

mac-physic

max-frame-size

power

} |

med-tlv

{

all

capability

inventory

location-id

{

civic-address

device-type country-code

{

ca-type ca-value

}&<1-10> |

elin-address

tel-number

} |

network-policy

power-over-ethernet

}

undo lldp

tlv-enable

{

basic-tlv

{

all

port-description

system-capability

system-description

system-name

} |

dot1-tlv

{

all

port-vlan-id

protocol-vlan-id

vlan-name

} |

dot3-tlv

{

all

Содержание photosmart 850









































































































































Результаты поиска

Содержание photosmart 850

Отзывы:

Бренды по названию

Популярные бренды

HP photosmart 850, Справочник по командам

Результаты поиска

Содержание photosmart 850

Отзывы:

Бренды по названию

Популярные бренды