HP photosmart 850 Скачать руководство пользователя

Страница: 120 / 136

115

Field Description

DEFAULT

Indicates whether a type of TLV is sent through a port by default.

Basic optional TLV

Basic TLVs:

•

Port description TLV.

•

System name TLV.

•

System description TLV.

•

System capabilities TLV.

•

Management address TLV.

IEEE 802.1 extended TLV

IEEE 802.1 organizationally specific TLVs:

•

Port VLAN ID TLV.

•

Port and protocol VLAN ID TLV.

•

VLAN name TLV.

IEEE 802.3 extended TLV

IEEE 802.3 organizationally specific TLVs:

•

MAC-Physic TLV.

•

Power via MDI TLV.

•

Link aggregation TLV.

•

Maximum frame size TLV.

LLDP-MED extend TLV

LLDP-MED TLVs:

•

Capabilities TLV.

•

Network Policy TLV.

•

Extended Power-via-MDI TLV.

•

Location Identification TLV.

•

Inventory TLV, including hardware revision TLV, firmware revision TLV,

software revision TLV, serial number TLV, manufacturer name TLV,

model name TLV, and asset id TLV.

lldp admin-status

Use

lldp admin-status

to specify the LLDP operating mode for a port or all ports in a port group.

Use

undo lldp admin-status

to restore the default LLDP operating mode.

Syntax

lldp admin-status

{

disable

txrx

}

undo lldp admin-status

Default

The LLDP operating mode is

TxRx

Views

Layer 2 Ethernet interface view, port group view

Default command level

2: System level

Parameters

disable

: Specifies the

Disable

mode. A port in this mode does not send or receive LLDP frames.

Содержание photosmart 850









































































































































Результаты поиска

Содержание photosmart 850

Отзывы:

Похожие инструкции для photosmart 850

Бренды по названию

Популярные бренды

HP photosmart 850, Справочник по командам

Результаты поиска

Содержание photosmart 850

Отзывы:

Похожие инструкции для photosmart 850

Бренды по названию

Популярные бренды