HP photosmart 850 Скачать руководство пользователя страница 10

Страница: 10 / 136

Table 1

Command output

Field Description

GigabitEthernet1/0/1 current state

Physical state of the Ethernet interface. For more information, see

Table

IP Packet Frame Type

Ethernet framing format on the interface.

Loopback

Loopback testing status of the interface.

1000Mbps-speed mode

The interface is operating at 1000 Mbps.
This field displays

Unknown-speed mode

when the interface is

disconnected from the peer with which it will automatically negotiate a

port speed.

full-duplex mode

The interface is operating in full-duplex mode.
This field displays

link duplex type is force link

when the duplex mode

of the interface is fixed and not configurable.

Link speed type is autonegotiation

The interface will negotiate a speed with its peer.

link duplex type is autonegotiation

The interface will negotiate a duplex mode with its peer.

The Maximum Frame Length

Maximum Ethernet frame length allowed on the interface.

Broadcast MAX-ratio

Broadcast suppression threshold as a percentage of the maximum
interface rate. When the threshold is exceeded, the interface drops

broadcast packets.

Unicast MAX-ratio

Unknown unicast suppression threshold as a percentage of the
maximum interface rate. When the threshold is exceeded, the

interface drops unknown unicast packets.

Multicast MAX-ratio

Multicast suppression threshold as a percentage of the maximum
interface rate. When the threshold is exceeded, the interface drops
multicast packets.

Allow jumbo frame to pass

Jumbo frames are allowed to pass through the interface.

PVID

Port VLAN ID.

Port link-type

Link type of the interface:

•

access

•

trunk

•

hybrid

Tagged VLAN ID

VLANs for which the interface sends packets without removing VLAN
tags.

Untagged VLAN ID

VLANs for which the interface sends packets after removing VLAN
tags.

Last clearing of counters: Never

Time when the

reset counters interface

command was last used to clear

statistics on the interface.

Never

indicates that the

reset counters

interface

command was never used since the device was started.

Last 300 seconds input: 0
packets/sec 0 bytes/sec
Last 300 seconds output: 0

packets/sec 0 bytes/sec

Average rate of input and output traffic in the last 300 seconds, in pps
and Bps.

Содержание photosmart 850









































































































































Результаты поиска

Содержание photosmart 850

Отзывы:

Бренды по названию

Популярные бренды

HP photosmart 850, Справочник по командам

Результаты поиска

Содержание photosmart 850

Отзывы:

Бренды по названию

Популярные бренды