![background image](http://html.mh-extra.com/html/hp/jetdirect-640n/jetdirect-640n_administrators-manual_163697045.webp)
Table 3-2
TFTP configuration file parameters (continued)
AppleTalk
appletalk:
(or
at-config:
,
ethertalk:
)
Use AppleTalk (EtherTalk) protocol operation on the print server.
0
: Disable.
1
(default): Enable.
NOTE:
On HP Jetdirect 640n print servers, all network protocols except TCP/IP are disabled by factory default.
DLC/LLC
dlc/llc-config:
(or
dlc/llc:
)
Use DLC/LLC protocol operation on the print server.
0
: Disable.
1
(default): Enable.
NOTE:
On HP Jetdirect 640n print servers, all network protocols except TCP/IP are disabled by factory default.
Other Settings
link-type:
(For wired 10/100/1000T Ethernet.) Set the print server's link speed (10, 100, 1000 Mbps) and communication mode
(Full- or Half-Duplex). The available link-speed depends on the print server model. The communication modes are:
AUTO
,
1000FULL
,
100AUTO
,
100FULL
,
100HALF
,
10FULL
,
10HALF
.
For
AUTO
(default), the print server uses auto-negotiation to configure the highest link speed and communication mode
allowed. If auto-negotiation fails, either
100TX HALF
or
10TX HALF
is set, depending on the detected link speed of the
hub/switch port. (A 1000T half-duplex selection is not supported.)
upgrade:
Set the name and location of a firmware upgrade file for the HP Jetdirect print servers.
CAUTION:
Ensure that command parameters are properly entered. Verify that the upgrade file is a higher version
than the currently installed version. The print server attempts to upgrade when the upgrade file contains a higher
version than the installed version.
The following is the command format:
upgrade: <TFTP server IP> <Version> <Product Number> <Filename>
The following defines the parameters:
<TFTP Server IP>
IP address of the TFTP server.
<Version>
Firmware version of the upgrade file.
<Product Number>
Print server product number.
<Filename>
Path and filename of the firmware upgrade file.
hw-acclrn-conf
Use hardware acceleration.
0
: Disable.
1
(default): Enable.
status-page-lang:
Page description language (PDL) that the print server uses to send the HP Jetdirect configuration/status page to the
printer.
◦
Auto
(default): Auto-detected when the print server is turned on or after a cold reset.
◦
PCL
: Hewlett-Packard Printer Control Language.
◦
ASCII
: Standard ascii characters.
ENWW
IPv4 configuration
35
Содержание Jetdirect 640n
