Table 4-13
Miscellaneous Settings (continued)
Item
Description
Certificate Mgmt Service
Allow HP Web Jetadmin to access and service your certificate configuration.
Web Services Print
Use the Microsoft Web Services for Devices (WSD) Print services supported on the
HP Jetdirect print server.
WS-Discovery
Use the Microsoft Web Services Dynamic Discovery (WS Discovery) protocols on the
print server.
LLMNR
Indicates whether link local multicast name resolution (LLMNR) requests are responded
to over IPv4 and IPv6.
Link settings
(For wired 10/100/1000T Ethernet) Set the print server's link speed and communication
mode. The available selections depend on the print server model.
CAUTION:
If you change the link setting, network communications with the print server
and network device might be lost.
●
AUTO
(default) Use auto-negotiation to configure itself with the highest link speed
and communication mode allowed. If auto-negotiation fails, either 100TX HALF or
10TX HALF is set, depending on the detected link speed of the hub/switch port. (A
1000T half-duplex selection is not supported.)
●
10T-Full
10 Mbps, full-duplex operation.
●
10T-Half
10 Mbps, half-duplex operation.
●
100TX-Full
100 Mbps, full-duplex operation.
●
100TX-Half
100 Mbps, half-duplex operation.
●
100TX-AUTO
Limit auto-negotiation to a maximum link speed of 100 Mbps.
●
1000T FULL
1000 Mbps, full-duplex operation.
Locally Administered Address
(Supported print servers only) Warning: Changing the locally administered address
results in the loss of connectivity to the browser.
Specify a locally administered address (LAA) to replace the factory assigned LAN
Hardware (MAC) address. If used, enter a string of exactly 12 hexadecimal digits.
For Ethernet print servers, the LAA address must start with hexadecimal X2, X6, XA, or
XE, where X is any hexadecimal digit 0 through F.
The default address is the factory assigned address.
Syslog Facility
Identify the source facility of a message. Typically used to identify the source of selected
messages during troubleshooting. By default, the HP Jetdirect print server uses LPR as
the source facility code. However, you can use values of local0 through local7 to isolate
individual or groups of print servers.
HTTP Idle Timeout
Length of time after which an idle HTTP connection is closed. Applies to the time after
an HTTP request or response completes. Enter from 5 to 60 seconds. The default is 15.
Set to zero (0) to disable. (The TCP/IP idle timeout value is used.)
Dynamic Raw Port Setting
Specify additional ports for printing to TCP port 9100. Valid ports are 3000 to 9000,
which are application-dependent.
86
Chapter 4 HP Embedded Web Server (V.45.xx.nn.xx)
ENWW
Содержание Jetdirect 640n
