![background image](http://html.mh-extra.com/html/hp/jetdirect-640n/jetdirect-640n_administrators-manual_163697040.webp)
Table 3-2
TFTP configuration file parameters (continued)
mult-tcp-conn:
Allow multiple TCP connections.
0
(default): Enable multiple connections.
1
: Disable multiple connections.
TCP/IP Raw Print Ports
raw-port
: (or
addrawport:
)
Additional ports for printing to TCP port 9100. Valid ports are 3000 to 9000, which are application-dependent.
TCP/IP Access Control
allow: netnum [mask]
Add entries to the host access list stored on the HP Jetdirect print server. Each entry specifies a host or network of
hosts allowed to connect to the printer. The
netnum
parameter sets the network number or host IP address, and
mask
sets an address mask of bits applied to the network number and host address to verify access. Add up to 10 access list
entries. If there are no entries, all hosts are permitted access. For example:
allow: 192.0.0.0 255.0.0.0
Allow hosts on network 192.
allow: 192.168.1.2
Allow a single host. The default mask 255.255.255.255 is assumed and is not required.
allow: 0
Clear the host access list.
For additional information, see
Security features (V.45.xx.nn.xx) on page 121
.
TCP/IP Other Settings
syslog-config:
Allow syslog server operation on the print server:
0
: Disable.
1
(default): Enable.
syslog-svr:
(or
syslog-srv:
)
IP address of the server that the HP Jetdirect print server sends syslog messages to.
syslog-max:
Maximum number of syslog messages sent by the HP Jetdirect print server on a per-minute basis. Allows
administrators to control the log file size.
0
: No restriction on the number of messages.
10
(default): Send a maximum
of 10 messages per minute.
syslog-priority:
Filter messages sent to the syslog server. The filter range is 0 to 7, with 0 being the most specific, and 7 the most
general. Only messages that are lower than the specified filter level (or higher in priority) are reported.
7
(default):
Messages of all priorities are sent.
8
: Disable. No syslog messages are sent.
syslog-facility:
Identify the source facility of a message. Typically used to identify the source of selected messages during
troubleshooting. By default, the HP Jetdirect print server uses LPR as the source facility code. Use values of
local0
through
local7
to isolate individual or groups of print servers.
slp-config:
Use the service location protocol (SLP) operation on the print server.
0
: Disable.
1
(default): Enable.
30
Chapter 3 TCP/IP configuration
ENWW
Содержание Jetdirect 640n
