Table 3-3
Telnet Commands and Parameters (continued)
ipsec-config
firewall-config
NOTE:
The
ipsec-config
command is available on print servers that support both
IPsec and Firewall configuration. The
firewall-config
command is available on full-
featured print servers that do not support IPsec, but allow Firewall configuration.
Disable IPsec or Firewall operation on the print server after IPsec/Firewall policies are
configured and enabled. You cannot enable IPsec/Firewall operation using this
command. Instead, use the HP Embedded Web Server to configure and enable IPsec/
Firewall polices.
0
: Disable IPsec/Firewall operation.
1
: (Read Only) IPsec/Firewall policies are configured and enabled.
ip
IP address for the print server. For example:
ip-config manual
ip 192.168.45.39
In the example,
manual
signifies manual configuration and
ip
sets the IP address on
the print server.
To clear the IP address, set the value to 0.0.0.0.
If you change this IP address, you must use it on the next Telnet connection.
subnet-mask
Identify the network and host portions of an IPv4 address in received messages. For
example:
subnet-mask 255.255.255.0
In the example, 255.255.255.0 is stored on the print server. To clear the subnet IP
address and disable the mask, set the value to 0.0.0.0.
NOTE:
If the HP Jetdirect print server is configured by DHCP and you manually
change the subnet mask or the default gateway address, you should also change the
print server's IP address. This releases the assigned DHCP address back to the DHCP
IP address pool.
default-gw
IP address of a default gateway used by the print server. For example:
default-gw 192.168.40.1
In the example, 192.168.40.1 is the IP address of the default gateway.
NOTE:
If the HP Jetdirect print server is configured by DHCP and you manually
change the subnet mask or the default gateway address, you should also change the
print server's IP address. This releases the assigned DHCP address back to the DHCP
IP address pool.
parm-file
Path and file name whose contents are printed each time the print server is turned on.
Enter up to 64 alphanumeric characters.
Config Server
(Read only.) IP address of the server (such as a BOOTP or DHCP server) that last
configured the IP address on the HP Jetdirect print server.
TFTP Server
(Read only.) IP address of the TFTP server that provided parameters to the HP Jetdirect
print server.
TFTP Filename
(Read only.) Path and TFTP filename on the TFTP server. For example:
hpnp/printer1.cfg
ENWW
IPv4 configuration
47
Содержание Jetdirect 640n
