Hoval BioLyt 100, Техническая информация Инструкции по установке

Страница: 30 / 52

4.7
Fitting the casing BioL
yt
(100-160)
Attachment set
A, C
NOTICE Before proceeding
with the installation
of the casing, make sure that all the cables and electrical
connections to the automatic firing device have been fitted.
27.
Fit the thermal insulation mats (30, 30a, 30b, Fig. 35, page 31 and 5, 5a, 5b Fig. 24, page 23).
28.
Slide
the middle
side walls
(31) into the plinth
rails and hook into the slots of the attachment brackets
above.
29.
Hook
the
controller
box
(32)
on
the
right
or
left
middle
side
wall
(position
depending
on
the
automatic
firing
device).
Additionally
secure
the controller
box
with
2 self-tapping
screws
Ø 3.5 mm at the top. Route
the
temperature sensor for the safety temperature limiter (STB) to the back of the boiler
and insert it into the
immersion sleeve (with boiler temperature sensors) and secure with the capillary
support spring. Connect
safety temperature limiter by fitting flat plug onto mounting tongues 1 and 2.
30.
Only on BioL
yt (130-160):
Mount the rear side walls (33) (route bolts on the bottom of the side wall (boiler
plinth rail) into the holes provided).
31.
Loosely
fit
protection
plate
(34a,
Fig.
33
and
Fig.
34)
to
the
left
and
right
top
side
wall
(34,
Fig.
33
and
Fig.
35).
H
oo
k
in
th
e
si
de
w
al
ls
. Position
and adjust the protection
plates and attach to the pellet
hopper
(serrated
washer must be used for the earth connection).
Attach speed nuts (C-clips, 34c) (C).
32.
Mount the top sections of the rear wall (35, 35a) using self-tapping screws (A).
33.
Mount the middle sections of the rear walls (36, 36a) using self-tapping screws (A).
34.
Take
off
sight
glass.
Mount
the
bottom
section
of
the
rear
wall
(37)
using
self-tapping
screws
(A).
Mount
the ground cable (on the
AA
T
cable) in the positions provided (on left
or right side of
the recess) using
self-tapping screws. Fit the ash discharge motor cover (37a). Refit the sight glass.
35.
Fit the rear covers (38, 38a).
36.
Fit the front cover (39) (must be fitted before installing the discharge hoses).
37.
Insert the right and left burner
cover at the bottom (40, 40a) on the screw heads
provided
and
press against
the casing side panels at the top.
38.
Place the front
burner cover (41) on the two supports (41a)
and screw onto the protection plates (34a) at
the top. Hook in the front hood (41b) (pay attention to the slots).
39.
Put the earthing
of the cable
of the HFR motors on the earthing
plates (Fig. 36, detail
W). Screw cover plate
(42) to both rear side walls and cover plate (42a) to the middle side wall (A).
NOTICE For 35, 35a, 36, 36a, 37, 37a, 42 and 42a (Fig. 35), a serrated washer must be used for one of the self-tapping screws (Fig. 37, detail X) (earth connection).
Fig. 33
34
34a 34c
Fig. 34
Note: Insert cover
(39) before
mounting the suction hoses.
4212946_Bid 33
32-BioLyt (100-160) / grma / 28.03.2014 M 1 : 5
4212946_Bid 34
32-BioLyt (100-160) / grma / 28.03.2014 M 1 : 5
30 4 214 852 / 01
ASSEMBLy BIOLyT (100-160)