Hoval BioLyt 100, Техническая информация Инструкции по установке

Страница: 26 / 52

4.5
Fitting the pellet hopper BioL
yt
(100-160)
Attachment set
A, F (Fig. 29)
19.
Mount the attachment bracket (20, in
the casing
package)
for the pellet
hopper:
the angular
rails
are screwed
onto the boiler
with nuts M8 plus
U-washers
from
below
on BioL
yt (130-160)
and from above on BioL
yt (100) respectively
(A).
The brackets can be screwed
on on the right or left. Slide the pellet hopper
into
position
before
the
final
tightening
of the
nuts, and
align
it with
the
connection
tube
(22)
on
the
burner
mechanism.
Align
the
attachment
bracket
on
the
rear
to
dimension 790 mm (on BioL
yt (130-160)) or dimension 832 mm (on BioL
yt (100)) respectively
.
20.
Slide the pellet hopper (21) into the attachment brackets, screw it to the brackets with M8x20 (F) (BioL
yt (130-160)) or M8x70 (BioL
yt (100)).
21.
Connect the connection tube (22) to the metering tube using a self-locking clip. Do not forget the gasket!
22.
Fit induced-draught fan (24) (4 pcs. - nut M8 with washer and circlip).
23.
Screw
clampin
g
plate
with
automatic
firing
device
(25)
on
the
side
of
the
pellet
hopper
(21)
(unscrew
the
self-trapping
screws,
hook
in
the
clamping
plate,
re
-
tighten the screws).
NOTICE •
The
automatic
firing
device
must
be
mounted
on
the
burner
swivel
side.
To
change
the
combustion
chamber
door
attachment
side,
see
chapter
4.1 for BioL
yt (100-160).
•
Do not remove any unnecessary self-trapping screws in the pellet hopper
.
They are used for sealing (keyword: suction turbine negative pressure).
24.
Fit the metering
screw (26, top screw) inside
the metering
tube (pellet
hopper)
and
secure
with hex socket screws
M8x60
(with circlips,
screws and
spacers
supplied with the metering screw). Do not forget the gasket.
25.
Cab
le ducts (27) must be fitted on the same side as the automatic firing device (25) ((A) 4 pcs. - nut M6 with washer).
26.
Mounting
the
pellet
suction
turbine
(23,
option).
Mount
the
edge
protection
profile
(23b)
in
the
pellet
hopper
at
position
(23a).
Place
the
suction
system
(23)
on
the four M6 threaded
bolts. Place
a plastic
insulating
sleeve
(23c) (collar
downward)
and
a tall washer
(23d)
on each bolt and
then secure the suction system
with wing nuts (23e). Route the extension cable of the suction system to the rear along
the centre of the hopper
and between
hopper and boiler downward
to the
automatic
firing
device.
Establish
a
connection
in
accordance
with
the
wiring
diagram.
When
routing
the
cable
ensure
that
it
cannot
touch
the
heating
surface
cleaner mechanism (HFR, Fig. 31, page 29).
The sound attenuation cowl is placed later during the installation of the casing (43, Fig. 35, page 31).
Figure shows BioL
yt (130-160)
*on BioL
yt (100)
Dimension 832 mm
26 4 214 852 / 01
ASSEMBLy BIOLyT (100-160)