Honeywell VX3Plus Скачать руководство пользователя страница 141 | Manualshive

Страница: 141 / 282

Honeywell VX3Plus Скачать руководство пользователя страница 141

Misc

Options on this tab configure device specific options. Note that options not available on the VX3Plus are dimmed or grayed
out.

CapsLock

By default, CapsLock is disabled after a warmboot. To enable CapsLock after a warmboot, click this checkbox.

Touch Screen Disable

By default, the VX3Plus touchscreen is enabled. To disable the touchscreen after a warmboot, click this checkbox.

Enable RFTerm Auto Launch

This option is enabled by default. This option, when disabled (unchecked) stops RFTerm from launching at bootup. When
RFTerm is not installed or has not been added to the registry

Launch

sequence, this checkbox is ignored at bootup.

Enable Auto Launch IP Wait

When enabled, this feature works as follows:

1. After the radio .CAB file is unpacked, the Launch program waits for the radio driver to load and for the radio to connect

and obtain an IP address.

2. During the wait, a message window is displayed containing the NDIS communication messages up to and including the

display of the valid IP address.

3. After the IP address is obtained, the message window is displayed for one second and then removed.

4. Launch completes its normal task path, unpacking any remaining .CAB files and completing any remaining tasks.

5. If an IP address is not obtained within the specified timeout period (see below), Launch completes its normal task path.

The default is unchecked (disabled). Launch does not wait for an IP address.

3-101

«
...
139
140
141
142
143
...
»

Содержание VX3Plus



























































































































































































































































































Отзывы:

Нет отзывов