Honeywell NOTIFIER AM-8200 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 46

Honeywell NOTIFIER AM-8200 Скачать руководство пользователя страница 14

AM-8200

Installation Manual

PAGE - 11

AM8200_manu-inst

Doc. M-162.2-AM8200-ENG Rev A.2

NOTIFIER ITALIA

Batteries Installation

Place the Bi-adhesive pads on the metal chassis and place the batteries on it.

Power supply and battery operation

The main microprocessor of the control unit periodically checks the state of the main AC power supply

source, batteries and the recharging circuit. The control unit will automatically switch on the stand-by battery
source when AC mains fails.

When the control unit operates through AC mains, the main microprocessor controls the battery charger output

and the presence of them. To perform this test, the output battery charger is temporarily switched off and the
battery voltage is read (signaling of missing batteries<15.0V).

When the control unit operates as a battery (in the absence of the AC mains) “Low Battery” breakdown will be
indicated when their voltage is <21.5V and, to prevent irreversible damages the voltage will be automatically
switched off, by disconnecting the batteries, when the voltage is < 19,5V.

All wirings MUST be checked BEFORE they are connected to the control unit.
It is recommended to perform at least the following checks:

Bi-adhesive pads

Bi-adhesive pads

«
...
12
13
14
15
16
...
»

Содержание NOTIFIER AM-8200















































Отзывы:

Нет отзывов