manualshive.com logo in svg

Honeywell MAXPRO NVR Hybrid PE, Руководство по установке и настройке оборудования

Поделиться
Скачать
Honeywell MAXPRO NVR Hybrid PE Скачать руководство пользователя страница 133

. . . . .

C O N F I G U R I N G   M A X P R O   N V R

Configuring the Cameras

MAXPRO NVR 5.0 Installation and Configuration Guide

133

9.

Under 

General > Preference > Stream Preference Settings

•

Live

 - Select the preferred stream of the camera which you want to use for streaming 

live video.

•

Continuous

 - Select the preferred stream of the camera which you want to record 

continuously. 

•

Event Recording

 - Select the preferred stream of the camera which you want to 

record on events.

•

Mobile/Web

 - Select the preferred stream of the camera which you want to use for 

streaming in Mobile/Web application.

•

High Resolution

 - Select the preferred stream of the camera which you want to 

categorize as High Resolution stream.

•

Low Resolution

 - Select the preferred stream of the camera which you want to 

categorize as Low Resolution stream.

Note:

The stream selected as Low Resolution settings will be used in SMART VMD.

•

Multicast Enabled

 - Select this check box to enable the Multicast feature for the 

camera. After selecting the check box enter the following details:

•

Multicast Address

: Type the Multicast IP address.

•

Multicast Port

: Type the Multicast IP Port number.

10.

Under 

Primary Stream > Recording > Video Quality Settings

•

Resolution

 - The 

Resolution

 is defaulted to a fixed value based on the camera 

model (for example, HD3MDIP model defaults to 1280 x 720 resolution).

•

Frame Rate

 - Select the 

FPS

 for a camera. FPS refers to the number of pictures 

displayed in exactly one second. FPS is a measure of how much information is used 
to store and display motion video. The term applies to digital video. Each frame is a 
still image; displaying frames in quick succession creates the illusion of motion.

Note:

30 FPS is the maximum frame rate in NTSC format and 25 FPS is the maximum
frame rate in PAL format supported by MAXPRO NVR.

Ensure that you set the Primary stream for recording which is 720p resolution and
secondary stream for Live which is 4CIF. See 

Recommended stream Settings

section for more information. 

You can set the Bit rate value in the specific camera web page.

•

Video Codec Type

 - Select the Codec type for the camera. The available options are 

H.264, H.265 and MJPEG. H.265 cameras can render in both CPU and GPU modes.

Limitations of H.265 Codec Type

:

•

H.265 is not supported in MAXPRO Mobile app

•

H.265 is not supported in Web client. 

Содержание MAXPRO NVR Hybrid PE









































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды