manualshive.com logo in svg

Honeywell ADEMCO Vista-12C, Инструкция по установке и настройке

Поделиться
Скачать
Honeywell ADEMCO Vista-12C Скачать руководство пользователя страница 98

Installation and Setup Guide 

 

 

7-2 

hours 55 minutes of Test mode), the keypad emits a double-beep every 30 seconds to alert 
that the end of  
Test mode is nearing. 

 

Checking Zones Using One-Man Walk Test (Sniffer Mode) 

Use this mode to test all zones (wired and wireless) that have been programmed. Make sure 
all partitions are disarmed before trying to enter this mode, since this is a system-wide 
command. 
1.  Press [Installer code] + [#] + 3. 

NOTE:

 If the communicator is in the process of sending a report to the central station, 

the system will not go into the Sniffer mode. If so, wait a few minutes, and try 
again. 

The keypads in all partitions will display all zone numbers (in all partitions) 
programmed in the system. Fault each zone in turn, causing each one to send a signal.

 

As the system receives a signal from each of the zones, the corresponding zone number 
disappears from the display.  

2.  After all zones have been checked, exit the Sniffer Mode by keying [Installer code] + 

OFF.    

IMPORTANT:

 Sniffer mode does not automatically expire. You must manually exit Sniffer 

Mode (by entering [Installer code] + OFF) to return to normal operation. 

NOTES: 

•  All BR type RF units (e.g., 5804) must physically be activated to clear the display. 
• When 

one

 button of a transmitter (RF, UR, or BR) is activated, all zones assigned to other 

buttons on that transmitter are cleared. This also applies to multiple-loop transmitters  
(e.g., 5816 and 5817).  

•  Any transmitter not “enrolled” or any zone that is not faulted will not turn off its zone 

number. 

Go/No Go Test Mode 

The Go/No Go Test verifies adequate RF signal strength from the proposed transmitter 
location, and allows you to reorient or relocate transmitters if necessary, before mounting the 
transmitters permanently. This mode is similar to the Transmitter Test mode, except that 
the wireless receiver gain is reduced. This will enable you to make sure that the RF signal 
from each transmitter is received with sufficient signal power when the system is in the 
normal operating mode.  
1.  Enter [Installer code] + [#] + 4 from the partition being tested. Repeat this test for each 

partition. 

2.  After you have placed transmitters in their desired locations and the approximate length of 

wire to be run to sensors is connected to the transmitter's screw terminals (if used), fault 
each transmitter. Do not conduct this test with your hand wrapped around the transmitter. 
a.  Keypad beeps three times to indicate signal reception and displays the appropriate zone 

number. 

b.  If the keypad does not beep, you should reorient or move the transmitter to another 

location. Usually a few centimeters in either direction is all that is required.

 

Содержание ADEMCO Vista-12C

















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды