Honeywell ADEMCO Vista-12C Скачать руководство пользователя страница 81

Страница: 81 / 112

Menu Mode Programming

5-25

PROMPT

VALID ENTRIES

EXPLANATION

9 0 A l m / T r b l P r o c

Alarm/Trouble
Processing

0 = none
1 = Zone type has automatic

restore

2 = zone type uses Misc. Fault

Delay Time and automatic
restore

[

∗

] to continue

Select desired actions for zones assigned to this
zone type.

Option 2: Select Miscellaneous Fault Delay in
field *87.

NOTE:

If 6 was selected above for the Zone

Attribute, enter 0 for this prompt.

9 0 T R B L S O U N D

Trouble Sounding

0 = none
1 = one beep every minute
2 = normal trouble sound (fast

beeps)

[

∗

] to continue

Select type of sounding upon trouble conditions on
zones assigned to this zone type.

9 0 A L A R M S O U N D

Alarm Sounding

0 = none
1 = keypad sound only
2 = steady siren sounding
3 = pulsing siren (temporal)
[

∗

] to continue

Select type of sounding upon alarm conditions on
zones assigned to this zone type.

9 0 D i a l D e l a y

0 = N o , 1 = Y e s

Dial Delay?

0 = no
1 = yes
[

∗

] to continue

If selected, faults on zones assigned to this zone
type will delay reporting for whatever length of
time that is selected in dial delay (*50).

9 0 D i s p O p t i o n

Display Options

0 = no display
1 = display only
2 = chime only
3 = chime & disp.
[

∗

] to continue

Select whether faults on zones assigned to this
zone type are displayed at the keypad and/or
cause a chime sound.

A l a r m I D : 0 0 0

T r o u b l e I D : 0 0 0

Contact ID Report Codes

000-999 = report code
[

∗

] to continue; returns to Enter

configurable zone type number
prompt.

Enter the desired 3-digit Contact ID report codes
for faults and troubles occurring on zones assigned
to this zone type.

IMPORTANT:

•

Make sure the code does not conflict with

existing, predefined Contact ID report codes.
See the

System Communication

section for a

list of standard Contact ID codes.

•

Zone alarm report code (prompt in *56 Zone

Programming) and Trouble report code (*60)
and relevant restore codes (*70, *71) must be
enabled in order for the Configurable Zone Type
codes to be reported.

Содержание ADEMCO Vista-12C
















































































































Результаты поиска

Содержание ADEMCO Vista-12C

Отзывы:

Бренды по названию

Популярные бренды

Honeywell ADEMCO Vista-12C, Инструкция по установке и настройке

Результаты поиска

Содержание ADEMCO Vista-12C

Отзывы:

Бренды по названию

Популярные бренды