Honeywell ADEMCO VISTA-120, Инструкция по установке и настройке

Страница: 78 / 114

VISTA-120 Installation and Setup Guide
6-8
Note that these codes are independent of the relay
codes programmed during
Output Programming in the
#93 Menu Mode located in the Programming Guide.
Relay Commands
Action Code Action Action Specifier
01 Relay On Relay #
02 Relay Off Relay #
03 Relay Close for 2 seconds Relay #
04
Relay Close XX minutes (set
in field 1*74)
Relay #
05
Relay Close YY seconds (set
in field 1*75)
Relay #
06 Relay Group On Relay Group #
07 Relay Group Off Relay Group #
08
Relay Group Close for 2
seconds
Relay Group #
09
Relay Group Close XX
minutes (set in field 1*74)
Relay Group #
10
Relay Group Close YY
seconds (set in field 1*75)
Relay Group #
Arm/Disarm Commands
Action Code Action Action Specifier
20 Arm-STAY Partition(s)
21 Arm AWAY Partition(s)
22 Disarm Partition(s)
23
Force Arm STAY (Auto-
bypass faulted zns)
Partition(s)
24
Force Arm AWAY (Auto-
bypass faulted zns)
Partition(s)
25 Arm INSTANT Partition(s)
26 Arm MAXIMUM Partition(s)
The auto-arm warning (field 2*06) applies when
using Time-Driven events to auto-arm.
Temporary schedules do not override an auto-
arming or auto-disarming programmed in Time-
Driven events.
The auto-arming time period cannot be extended
using the Installer Code + #82 Mode.
Bypass Commands
Action Code Action Action Specifier
30 Auto bypass – Zone list Zone list #
31 Auto unbypass – Zone list Zone list #
Open/Close Time Periods
Action Code Action Action Specifier
40
Enable Opening Time Period
by partition
Partition(s)
41
Enable Closing Time Period
by partition
Partition(s)
42
Enable Access Time Period
for access group
Access Group
Access Control Commands
Action Code Action Action Specifier
55 Access Point Grant Access Point #
56
Access Point Grant with
Override
Access Point #
57 Access Point Protect Access Point #
58 Access Point Bypass Access Point #
59 Access Point Lock Access Point #
60 Access Point Exit Access Point #
61 Access Point Group Grant Group #
62
Access Point Group Grant
with Override
Group #
63 Access Point Group Protect Group #
64 Access Point Group Bypass Group #
65 Access Point Group Lock Group #
66 Access Point Group Exit Group #
67 Access Point Partition Grant Partition #
68
Access Point Partition Grant
with Override
Partition #
69
Access Point Protect by
Partition
Partition #
70
Access Point Bypass by
Partition
Partition #
71
Access Point Lock by
Partition
Partition #
72 Access Point Exit by Partition Partition #
73 Access Point Trigger On Trigger #
74 Access Point Trigger Off Trigger #
77 Access Point Group Enable Group #
78 Access Point Group Disable Group #
3. Enter the desired activation time (when the
action is to take place). Select from:
Activation
Time
Description
01 Beginning of time period.
02 End of time period.
03 During time period only (on at beginning of
time period, off at end).
For example, if bypass is selected to activate
during the time period, zones in a zone list
are bypassed at the beginning of the time
period and unbypassed at the end of the time
period.
04 Beginning and end of time period (e.g., a
coffee break buzzer). In this example, if relay
pulse is selected, the relay pulses for 2
seconds at the beginning of the time period,
signaling the beginning of the coffee break.
At the end of the time period it pulses again,
signaling the end of coffee break.