Holtek HT32F54231 Скачать руководство пользователя страница 464

Страница: 464 / 576

Rev. 1.00

464 of 576

January 28, 2022

32-Bit Arm

Cortex

-M0+ MCU

HT32F54231/HT32F54241/HT32F54243/HT32F54253

21 Serial Peripheral Interface (SPI)

SPI Status Register – SPISR

This register contains the relevant SPI status.

Offset:

0x014

Reset value: 0x0000_0003

Reserved

Type/Reset

Reserved

Type/Reset

Reserved

BUSY

Type/Reset

RO 0

RXBNE

TXE

TXBE

Type/Reset WC 0 WC 0 WC 0 WC 0 WC 0 RO 0 RO 1 RO 1

Bits

Field

Descriptions

[8]

BUSY

SPI Busy flag

0: SPI not busy

1: SPI busy

In the master mode, this flag is reset when the TX buffer and TX shift register are

both empty and is set when the TX buffer or the TX shift register are not empty.

In the slave mode, this flag is set when SEL changes to an active level and is reset

when SEL changes to an inactive level.

[7]

Time Out flag

0: No RX FIFO time out

1: RX FIFO time out has occurred

Once the time out counter value is equal to the TOC field setting in the SPIFTOCR

bit in the SPIIER register is enabled. This bit is cleared by writing 1.

Note: This Time Out flag function is only available in the SPI FIFO mode.

[6]

Slave Abort flag

0: No slave abort

1: Slave abort has occurred

This bit is set by hardware and cleared by writing 1.

[5]

Mode Fault flag

0: No mode fault

1: Mode fault has occurred

This bit is set by hardware and cleared by writing 1.

[4]

Read Overrun flag

0: No read overrun

1: Read overrun has occurred

This bit is set by hardware and cleared by writing 1.

[3]

Write Collision flag

0: No write collision

1: Write collision has occurred

This bit is set by hardware and cleared by writing 1.

Содержание HT32F54231

































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание HT32F54231

Отзывы:

Holtek HT32F54231, Руководство пользователя, Страница: 464 / 576

Результаты поиска

Содержание HT32F54231

Отзывы: