manualshive.com logo in svg

Holtek HT32F54231, Руководство пользователя

Поделиться
Скачать
Holtek HT32F54231 Скачать руководство пользователя страница 230

Rev. 1.00 

230 of 576

January 28, 2022

32-Bit Arm

®

 Cortex

®

-M0+ MCU

HT32F54231/HT32F54241/HT32F54243/HT32F54253

14  General-Purpose T

imer (GPTM)

Pause Mode

In the Pause Mode, the selected STI input signal level is used to control the counter start/stop 

operation. The counter starts to count when the selected STI signal is at a high level and stops 

counting when the STI signal is changed to a low level, here the counter will maintain its present 

value and will not be reset. Since the Pause function depends upon the STI level to control the counter 

stop/start operation, the selected STI trigger signal cannot be derived from the TI0BED signal.

CK_ CNT

STI

CNT_ EN

27

CNTR

28

29

30

31

TEVIF

Sync.

Software clearing

STI source signal 

(polarity=0) 

STI source signal 

Sync.

(polarity=1) 

Figure 47.  GPTM in Pause Mode

Trigger Mode

After the counter is disabled to count, the counter can resume counting when an STI rising edge 

signal occurs. When an STI rising edge occurs, the counter will start to count from the current 

value in the counter. Note that if the STI signal is selected to be derived from the UEVG bit 

software trigger, the counter will not resume counting. When software triggering using the UEVG 

bit is selected as the STI source signal, there will be no clock pulse generated which can be used to 

make the counter resume counting. Note that the STI signal is only used to enable the counter to 

resume counting and has no effect on controlling the counter to stop counting.

CK_CNT

STI

CNT_EN

27

CNTR

(Up-counting)

29

30

31

32

TEVIF

Sync.

Software clearing

28

STI source signal 

(polarity=0)

STI source signal 

(polarity=1)

Figure 48.  GPTM in Trigger Mode

Содержание HT32F54231

































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды