119
W
at
er
S
ys
te
m
s -
6
2012 Trip
freSH Water
Pressurized Water Fill
When connecting to fresh water or when
filling the fresh water tank, use a hose
manufactured and labeled for “potable” water.
This ensures the hose and hose fittings are safe
for drinking water. It is recommended to install
a water pressure regulator at the water source
to protect the potable hose and plumbing
system from excess pressure.
WARNING:
Hose and hose fittings
not manufactured
for potable water can
contain unsafe levels
of lead. It is highly
recommended to use
only fresh water supply
hoses manufactured for
potable water use.
Connect one end of the
pressure regulator to the
water source and the
other end to the potable
hose.
Connect a potable hose
to the City Water/Fresh Tank
Fill connection located in the
roadside water service center.
Set the water control lever to
the Tank Fill position.
Turn on water at the source.
Periodically press the Test
switch on the monitor panel
to gauge fill rate. Do not
leave the
motorhome unattended while filling the
fresh water tank.
The tank is nearing full when the light
marked F illuminates. When the tank is
completely full, water will flow out an
overflow tube under the motorhome.
Turn off the water supply and return
the water control lever to the City
Water position.
Disconnect the potable hose. Remove
pressure regulator. Store the hose with
both ends connected to prevent debris
from entering the hose.
CAUTION:
It is recommended to place a
pressure regulator at the water
source to protect the potable water
system from over-pressurization.
Some water sources have high
water pressure, particularly in
mountainous regions. High water
pressure is anything over 55 psi
(pounds per square inch). Excessive
water pressure may cause leaks in
water lines and/or damage the water
heater. Excess pressure can cause the
water hose to swell and burst.
Gravity Fill
The gravity fill port located on the water
service center panel allows fluids to be
introduced directly into the fresh water tank.
Water can be poured directly from a container
into the fresh water tank. The gravity fill inlet
can be used to pour disinfecting solution into
the fresh water tank. Use only potable water
sources, solutions and delivery systems when
using the
gravity fill inlet.
Filling the Tank:
Unscrew fill cap taking care to keep
cap and inlet clean.
Insert potable water hose into inlet.
Fill tank until water overflows from inlet.
NOTE:
Do not leave the gravity fill inlet
unattended when in use.
City Water Hook-Up
When connecting the motorhome to
fresh water, use a hose manufactured and
labeled for potable water. It is required
to install a pressure regulator to prevent
over-pressurization of the fresh water
plumbing system. Attaching the regulator at
the water source will also protect the hose
from expanding and bursting due to excess
pressure.
Install the pressure regulator at the
water source.
Connect the potable hose to the City
Water/Fresh Tank Fill connection.
040480ya
040460o
Gravity Fill Port
040596mf
Gravity fill port located on water service
center panel
Содержание Trip 2012
