95
E
qu
ip
m
en
t -
5
2012 Trip
graB HanDle
The grab handle is used to aid in
entering and exiting the motorhome.
Cleaning the Handle:
Clean the acrylic grab handle using
mild Soap and Water only!
What Not To Use:
Do not
use alcohol or ammonia based
glass cleaners as these solutions
adversely affect acrylic material
causing stress cracks leading to
eventual failure of the grab handle.
Use of alcohol based cleaners
combined with heat and light will
expedite deterioration of the acrylic
material.
entry Door
The entry door is adjusted at the factory and
tested for all operations. The door uses two
separate locks for safety and security. One
locking system is the door lock and the other
is a dead bolt. The door handle incorporates a
primary and secondary latching system used to
ensure secure and safe latching. Adjustments
can be made to
help maintain
entry door
performance.
Adjusting the Entry Door Latch:
Determine which bolt needs
adjustment.
Slowly close the entry door,
observing the latch and strike
bolt alignment.
Do not
attempt
to latch if the alignment is off. If
the alignment is correct, allow
the latch to catch in the first
(primary) position only.
The latch should move to the
second position with only slight
pressure applied to the entry
door. Upper and lower latches should
be evenly timed. Press on the entry
door to check for further movement.
The entry handle should operate with
little effort to open the entry door.
Excess pressure indicates the bolts are
set too far back.
With a box wrench or socket, loosen
the movable strike bolt. Adjust in small
increments. Tighten the bolt firmly
after making adjustments. Bolts should
have slight up and down movement for
vibration control in travel.
Test the operation of the dead bolt lock
to ensure proper functions.
Apply silicone weekly to the entry door
rubber gaskets to prevent squeaking
while the motorhome is in use. Use
a 1" sponge paint brush sprayed with
silicone for easy application.
CAUTION
When operating the entry door, ensure
the dead bolt latch is fully unlocked
prior to closing. Failure to do so can
result in damage to the dead bolt and/
or entry door.
Changing Screen Door Glass:
The screen slider is Tuffak
®
. The
slider can be bowed for removal and
replacement.
Replace with new Tuffak and reverse
the procedure.
Adjusting the
Screen Door:
Loosen the
fasteners on the
hinge side of the
screen door: two on
the top and two on
the bottom.
The steel hinge has
slots to allow movement.
Four type screws are on the top hinge
and four on the bottom hinge to adjust
the screen door for proper fit to the
entry door. The hinge should fit tightly
to the trim of the door when the screen
door is latched to the door and the door
is open.
020130d
020131f
020129h
Loosen to adjust
070213
Содержание Trip 2012
