Hill-Rom FE5000 Скачать руководство пользователя страница 11

Страница: 11 / 108

Installation

Chapter 1: Introduction

Electrically Operated General Ward Bed

Page 1 - 3

Operation and Maintenance Manual

(154588 REV 1)

Installation

Unpack

and examine the bed. See the steps in the sections below.

Unpack the Bed

Unpack the bed:

1. Remove all of the bubble-wrap from the bed.

2. Remove the protective foam pad from the end of the bed (see figure 1-1 on

page 1-3).

Figure 1-1. Unpack the Bed

3. Remove the nylon ties from the safety siderails.

4. Remove the nylon ties from the backrest, thigh section, and the foot section.

5. Unpack the headboards and footboards. Put the headboards and footboards into

the sockets and tighten the tri-wheel screws.

6. Set all of the lockout switches on the attendant control panel to the unlocked

position. Go to “Attendant Control Panel” on page 1-8.

SHOCK HAZARD:

Make sure the power cable is in a position that is away from the bed frame
parts that move. Failure to correctly install the power cable can cause injury
or equipment damage.

Содержание FE5000













































































































Результаты поиска

Содержание FE5000

Отзывы:

Hill-Rom FE5000, Руководство по эксплуатации и обслуживанию, Страница: 11 / 108

Результаты поиска

Содержание FE5000

Отзывы: