Hill-Rom FE5000 Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 108

Hill-Rom FE5000 Скачать руководство пользователя страница 29

Specifications

Chapter 1: Introduction

Electrically Operated General Ward Bed

Page 1 - 21

Operation and Maintenance Manual

(154588 REV 1)

1

The electromagnetic emissions and immunity guidance is given below:

Electromagnetic Emissions Guidance

Guidance and Manufacturer's Declaration—Electromagnetic Emissions

The bed is intended for use in the electromagnetic environment specified below. The customer or the user of the bed

should assure that it is used in such an environment.

Emissions Test

Compliance

Electromagnetic Environment—Guidance

RF Emissions
CISPR 11

Group 1

The bed uses RF energy only for its internal function.
Therefore, its RF emissions are very low and are not likely
to cause any interference in nearby electronic equipment.

RF emissions
CISPR 11

Class A

The bed is suitable for use in all establishments other than
domestic and those directly connected to the public low-
voltage power supply network that supplies buildings used
for domestic purposes.

Harmonic emissions
IEC 61000-3-2

Class A

Voltage fluctuations / flicker
emissions
IEC 61000-3-3

Complies

«
...
27
28
29
30
31
...
»

Содержание FE5000













































































































Отзывы:

Нет отзывов