Hill-Rom FE5000 Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 108

Hill-Rom FE5000 Скачать руководство пользователя страница 28

Specifications
Chapter 1: Introduction

Page 1 - 20

Electrically Operated General Ward Bed

Operation and Maintenance Manual

(154588 REV 1)

Electrical Specifications

For electrical specifications, see table 1-2 on page 1-20.

Table 1-2. Electrical Specifications

Electromagnetic Emissions and Immunity Guidance

Electrostatic Discharge

When static charge builds up on a bed or on other equipment, an electrostatic
discharge (ESD) is produced which can damage electronic components.
Studies have shown that these discharges can reach 30 kv or higher.

Reduce the possibility of electrostatic discharge with these:

• See that the atmosphere does not become too dry.

• Use cotton-type bedding and cotton carpet.

• Use conditioner when cleaning the carpet.

Electromagnetic Interference

Patient monitoring equipment can become unreliable from the generation of
low frequency electromagnetic fields. Equipment such as the EEG
(Electroencephalograph) and the ECG (Electrocardiogram) operate in a low
frequency range (0-125 Hz) and can be changed by mains power (50-60 Hz)
frequency interference.

Condition

Range

AC Input Power Requirements

240 V AC +/- 10%, .6 A, 50 Hz

Battery Backup

1.2 ampere-hour

Enclosure

Double insulated with functional
earth connector, Class One,
indoor use only, IPX4

a

a. IPX4 is identified as:

(X) Protection against dust - limited degrees (no harmful deposits).
(4) Protection against water sprayed from all directions. Limited ingress

permitted. Provides complete protection against contact with live or moving
parts inside the enclosure. Protection against harmful deposits of dust.

«
...
26
27
28
29
30
...
»

Содержание FE5000













































































































Отзывы:

Нет отзывов