Hill-Rom FE5000 Скачать руководство пользователя страница 25

Страница: 25 / 108

Specifications

Chapter 1: Introduction

Electrically Operated General Ward Bed

Page 1 - 17

Operation and Maintenance Manual

(154588 REV 1)

Specifications

Physical Description

WARNING:

Do not use the product outside the recommended safe working load. To
do so could cause patient injury or equipment damage.

For a physical description, see table 1-1 on page 1-17. All maximum bed
angles shown are with respect to horizontal.

Table 1-1. Physical Description

Feature

Dimension

Maximum width (retracted extension) 1016 mm
Length (fully extended)

2405 mm

Length (fully retracted)

2210 mm

Trendelenburg (and reverse
Trendelenburg)

angle

Backrest inclination (maximum)

angle

Siderail height (above the sleep deck) 390 mm
Head/Footboard height above bed
deck

415 mm

Required wall clearance

160 mm

Under bed clearance (minimum)

125 mm

Horizontal movement of bed through
full height range

60 mm

Wheelbase

—150 mm single wheel

castors

220 mm

Wheelbase

—150 mm twin wheel

castors

205 mm

Wheelbase

—200 mm single wheel

castors

260 mm

Safe working loads (depends on
model numbers)

200 kg for model FE 5000_xxx20xxx
250 kg for model FE 5000_xxx25xxx
280 kg for model FE 5000_xxx28xxx
300 kg for model FE 5000_xxx30xxx

Bed weight (shipping weight)

145 kg

Содержание FE5000













































































































Результаты поиска

Содержание FE5000

Отзывы:

Hill-Rom FE5000, Руководство по эксплуатации и обслуживанию, Страница: 25 / 108

Результаты поиска

Содержание FE5000

Отзывы: