Hill-Rom FE5000 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 108

Hill-Rom FE5000 Скачать руководство пользователя страница 16

Features
Chapter 1: Introduction

Page 1 - 8

Electrically Operated General Ward Bed

Operation and Maintenance Manual

(154588 REV 1)

Knee-Break Operation (Optional)

• To raise the section, press the

Knee-break Up

control (E) until the

applicable position is reached.

• To lower the section, press the

knee-break Down

control (F) until the

applicable position is reached.

Backrest and Knee-Break Operation Combined

• To raise the backrest and knee-break together, press the

Backrest and

Knee Combined Up

control (I) until the applicable position is reached.

• To lower the backrest and knee-break together, press the

Backrest and

Knee Combined Down

control (J) until the applicable position is reached.

Chair Position Operation

• To go into a seated position, press the

Chair

Up

control (K).

• To go out of a seated position, press the

Chair

Down

control (L).

Attendant Control Panel

WARNING:

The control panel lockout system must be used when patients should
not operate the controls. Failure to operate the bed correctly may cause
injury.

The attendant control panel (ACP) permits one or all of the functions to be
locked out so that the bed can not be operated from the handset.

All models have a self-level feature. If the bed is in an angled position, self-
level will occur at the very low and very high positions. This is to prevent
collisions between the upper mattress frame and the lower wheelbase
assemblies. Also the bed will pause for a moment when level position is
reached.

The typical attendant control panel functions are as follows (see figure 1-4 on
page 1-9):

• Backrest (M)

• Knee-break (N)

• HI/LO (O)

• Trendelenburg (P)

• Bed level (V)

«
...
14
15
16
17
18
...
»

Содержание FE5000













































































































Отзывы:

Нет отзывов