Hill-Rom DuraStar Series Скачать руководство пользователя страница 88

Страница: 88 / 165

4.8 DuraStar™ Fixed Height Stretcher Upper Frame

Chapter 4: Removal, Replacement, and Adjustment Procedures

DuraStar™ Series Stretcher Service Manual (man268)

Page 4 - 31

Figure 4-14. Fixed Height Upper Frame Height Adjustment

2. Pull the four height adjustment pins (G) from the opposite end that the

screws (H) were removed.

3. Raise or lower the upper frame to the height determined in step 1 of the

removal procedure.

4. Install the four height adjustment pins (G) into both the head column (I)

and foot column base weldments (J).

NOTE:
The pins should protrude from the opposite side of the base weldments.

5. Using the 1/4" Allen™ wrench, install the screws (H) into the head column

base weldment (I) pins (G) and foot column base weldment (J) pins (G).

6. Fully seat the screws on the pins (see figure 4-14 on page 4-31).

7. To ensure proper operation of the DuraStar™ Fixed Height Stretcher,

perform the “DuraStar™ Fixed Height Stretcher Function Checks” on page
2-7.

m268_042

Содержание DuraStar Series






































































































































































Результаты поиска

Содержание DuraStar Series

Отзывы:

Hill-Rom DuraStar Series, Руководство по обслуживанию, Страница: 88 / 165

Результаты поиска

Содержание DuraStar Series

Отзывы: