Hill-Rom DuraStar Series Скачать руководство пользователя страница 77

Страница: 77 / 165

4.6 Caster

Chapter 4: Removal, Replacement, and Adjustment Procedures

Page 4 - 20

DuraStar™ Series Stretcher Service Manual (man268)

2. Slide the caster into the base of the stretcher (K) (see figure 4-8 on page

4-18).

3. Using the 7/16" open end wrench, install the caster screw (F) and use blue

Loctite®

adhesive to ensure the screws will stay in place.

4. Using the torque wrench, torque the caster screw (F) to 46 + 6 in-lb (5.2 +

0.7 N·m).

5. Using the hammer and the punch, tap the hex rod (I) back into place so that

the hole in the hex rod matches up to install screw (B).

6. Replace the pedal.

7. Install and tighten cap plug retainer (E), 1/4-20 screw (D) and new cap

plug (C).

8. Remove the 8" x 2" x 4" (20 cm x 5 cm x 10 cm) lumber.

9. Put the stretcher in the steer position by pressing down on the green steer

pedal.

10. Install the brake/steer link screw (B).

11. To ensure proper operation of the DuraStar™ Hydraulic Stretcher, perform

the “DuraStar™ Hydraulic Stretcher Function Checks” on page 2-4. To
ensure proper operation of the DuraStar™ Fixed Height Stretcher, perform
the “DuraStar™ Fixed Height Stretcher Function Checks” on page 2-7.

1. Loctite® is a registered trademark of Loctite Corporation.

Содержание DuraStar Series






































































































































































Результаты поиска

Содержание DuraStar Series

Отзывы:

Hill-Rom DuraStar Series, Руководство по обслуживанию, Страница: 77 / 165

Результаты поиска

Содержание DuraStar Series

Отзывы: